1.1范围IEC 60947的本部分规定了主要用于工业或类似用途的带螺钉式或无螺钉式夹紧装置的接线板的要求，并将其固定在支架上，以在铜导线之间提供电气和机械连接。本规范适用于连接圆形铜导线的接线板，无论是否经过特殊处理，其横截面在0.2 mm2和300 mm2（AWG 24/600 kcmil）之间，用于额定电压不超过交流1000 V、高达1000 Hz或直流1500 V的电路中。注:AWG是“美国线规”（Gage（US）=Gage（UK））kcmil=1000 cmil的缩写；1 cmil=1圆形密耳=直径为1密耳1密耳=1/1000英寸的圆形表面本标准可作为要求将特殊装置固定到导体上的接线端子的指南，例如快速连接终端或缠绕连接等通过穿过绝缘层的边缘或点与导体直接接触的接线板，例如绝缘位移连接等。 ;- 特殊类型的接线板，例如断开接线板等。在本标准适用的情况下，使用术语“夹紧装置”代替术语“端子”。在参考IEC 60947-1.1.1DV修改以添加以下内容时，应考虑到这一点:1.1DV。1根据附录DVB、国家电气规范、NFPA 70（美国使用）或CSA C22，本标准规定了主要用于工业或类似用途并固定在支架上的带螺钉式或无螺钉式夹紧装置的接线板的要求。1-15《加拿大电气规范》第一部分（适用于加拿大）和NOM-001-SEDE《电气装置（公用设施）》（适用于墨西哥）1.1DV。2本标准涵盖的接线板的导线范围包括0051 mm2至1 010 mm2（30 AWG至2000 kcmil）铜导线和3,31 mm2至1 010 mm2（12 AWG至2000 kcmil）铝导线。铝要求见附录DVA。 在墨西哥，不允许使用3,31 mm2（12 AWG）、5,26 mm2（10 AWG）和8,37 mm2（8 AWG）铝导线。1.1DV。3电压范围包括高达1500伏交流电和1500伏直流电。

1.1 ScopeThis part of IEC 60947 specifies requirements for terminal blocks with screw-type or screw-less-type clamping units primarily intended for industrial or similar use and to be fixed to a support to provide electrical and mechanical connection between copper conductors. It applies to terminal blocks intended to connect round copper conductors, with or without special preparation, having a cross-section between 0,2 mm2 and 300 mm2 (AWG 24/600 kcmil), intended to be used in circuits of a rated voltage not exceeding 1 000 V a.c. up to 1 000 Hz or 1 500 V d.c.NOTE AWG is the abbreviation of "American Wire Gage" (Gage (US) = Gauge (UK))kcmil = 1000 cmil;1 cmil = 1 circular mil = surface of a circle having a diameter of 1 mil1 mil = 1/1000 inchThis standard may be used as a guide for- terminal blocks requiring the fixing of special devices to the conductors, for example quick connect terminations or wrapped connections, etc.;- terminal blocks providing direct contact to the conductors by means of edges or points penetrating the insulation, for example insulation displacement connections, etc.;- special types of terminal blocks, for example disconnect terminal blocks, etc.Where applicable in this standard, the term "clamping unit" has been used instead of the term "terminal". This is taken into account in case of reference to IEC 60947-1.1.1DV Modification to add the following:1.1DV.1This standard specifies requirements for terminal blocks with screw-type or screw-less-type clamping units primarily intended for industrial or similar use and to be fixed to a support, in accordance with Annex DVB, National Electrical Code, NFPA 70 (for use in the USA), or CSA C22.1 - 15 Canadian Electrical Code, Part I (for use in Canada), and NOM-001-SEDE, Electrical Installations (Utility) ([for use in Mexico]).1.1DV.2The wire range for terminal blocks covered by this standard include 0,051 mm2 to 1 010 mm2 (30 AWG to 2 000 kcmil) copper conductors and 3,31 mm2 to 1 010 mm2 (12 AWG to 2 000 kcmil) aluminum conductors. See Annex DVA for aluminum requirements.In Mexico, 3,31 mm2 (12 AWG), 5,26 mm2 (10 AWG), and 8,37 mm2 (8 AWG) aluminum conductors are not allowed.1.1DV.3The voltage range includes up to 1 500 Vac and 1 500 Vdc.