请注意:此版本的所有临时修订版将在您购买时提供。安装在先前安装的荧光灯具上的灯具反射器套件的补充要求SUL 1598B1。1本标准适用于由一个或多个组件组成的反射器套件，这些组件将在灯具初始安装后的某个时间安装在荧光灯具中。这些要求是对灯具标准UL 1598中其他适用要求的补充。反射器套件的组件包括反射器、镇流器、灯座、配线、支架、导线连接器或类似物品。参考灯具标准UL 1598中的要求时，为便于识别，采用斜体。1.2表1.1根据反射器套件安装所涉及的任务，定义了本标准要求涵盖的反射器套件类型。 I型反射器套件的安装应仅涉及与表1.1中反射器套件类型相对应的任务。II型反射器套件能够完成I型和II型反射器套件的任务。表1.1反射镜套件类型反射镜套件类型涉及的任务I-反射镜安装-反射镜更换II-灯座重新定位、拆除或更换-镇流器重新定位、拆除或更换-电线重新定位、拆除、更换或添加1。3包含新特性、特性、组件、材料或系统的产品，或与本标准要求所涵盖的特性、特性、组件、材料或系统不同的产品，对于涉及火灾、触电或人身伤害风险的，应使用适当的附加部件和最终产品要求进行评估，以保持本标准意图最初预期的安全水平。 如果产品的特征、特性、组件、材料或系统与本标准的特定要求或规定相冲突，则该产品不符合本标准。应按照制定、修订和实施本标准所采用的方法，提出并采用要求的修订。

Please note: All interim revisions for this edition available at time of your purchase will be included.Supplemental Requirements for Luminaire Reflector Kits for Installation on Previously Installed Fluorescent LuminairesUL 1598B1.1 This Standard applies to reflector kits that consist of one or more components that are intended to be installed in fluorescent luminaires sometime after the initial installation of the luminaire. These requirements are supplementary to the other applicable requirements in the Standard for Luminaires, UL 1598. The components of a reflector kit are reflectors, ballasts, lampholders, wiring, brackets, wire connectors, or similar items. References to requirements in the Standard for Luminaires, UL 1598 are in italics for easy identification.1.2 Table 1.1 defines the types of reflector kits covered by the requirements in this Standard based on the tasks involved in the installation of a reflector kit. The installation of a Type I reflector kit shall involve only those tasks that correspond to its reflector kit type in Table 1.1. A Type II reflector kit is able to involve the tasks of kit types I and II.Table 1.1Reflector kit typesReflector kit typesTasks involvedI - Reflector installation- Reflector replacementII - Lampholder relocation, removal, or replacement- Ballast relocation, removal, or replacement- Wire relocation, removal, replacement, or addition1.3 A product that contains features, characteristics, components, materials, or systems new or different from those covered by the requirements in this standard, and that involves a risk of fire or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-product requirements to maintain the level of safety as originally anticipated by the intent of this standard. A product whose features, characteristics, components, materials, or systems conflict with specific requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and implementation of this standard.