首页 馆藏资源 舆情信息 标准服务 科研活动 关于我们
现行 ASTM F2435-22
到馆提醒
收藏跟踪
购买正版
Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe 钢增强聚乙烯(PE)波纹管标准规范
发布日期: 2022-02-01
1.1 本规范涵盖标称尺寸为8英寸的钢骨增强波纹聚乙烯(PE)管道系统的材料、尺寸、工艺、伸长率、抗冲击性、管道刚度、穿孔和标记的要求和测试方法。(200毫米),至80英寸。(2000毫米)。受本标准管辖的钢骨增强聚乙烯管拟用于地下应用,其中土壤为其柔性壁提供支撑。受本标准管辖的钢骨增强聚乙烯波纹管适用于非- 卫生下水道、雨水管和排水管的压力应用。 1.2 以英寸-磅为单位的数值应视为标准值。括号中给出的值是到国际单位制的数学转换,仅供参考,不被视为标准值。 1.3 没有类似或等效的ISO标准。 1.4 本标准并非旨在解决与其使用相关的所有安全问题(如有)。本标准的用户有责任在使用前制定适当的安全、健康和环境实践,并确定监管限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒(TBT)委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 4.1 钢筋波纹PE管用于地下应用,土壤为其柔性壁提供支撑。其主要用途是收集或输送雨水- 关闭下水道和排水沟,或同时关闭。 4.2 建议使用的除外条款: 4.2.1 永久暴露在阳光下以及暴露在与管道和配件相容性未知的化学品中。
1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, impact resistance, pipe stiffness, perforations, and markings for steel reinforced corrugated polyethylene (PE) piping systems of nominal sizes 8 in. (200 mm), through 80 in. (2000 mm). The steel reinforced polyethylene pipes governed by this standard are intended for use in underground applications where soil provides support for their flexible walls. The steel reinforced polyethylene corrugated pipes governed by this standard are intended for use in non-pressure applications for sanitary sewers, storm sewers and drainage pipes. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 There is no similar or equivalent ISO standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 Steel reinforced corrugated PE pipes are used for underground applications where soil provides support to their flexible walls. Their major use is to collect or convey storm water run-off for sewers and drains, or both. 4.2 Exclusions from recommended use: 4.2.1 Permanent exposure to sunlight and exposure to chemicals whose compatibility with the pipe and fittings is not known.
分类信息
关联关系
研制信息
归口单位: F17.62
相似标准/计划/法规
现行
AASHTO M 335-19(2023)
Standard Specification for Steel-Reinforced Polyethylene (PE) Ribbed Pipe, 300- to 1500-mm (12- to 60-in.) Diameter
300-1500mm(12-60in.)钢增强聚乙烯(PE)带肋管标准规范直径
现行
AASHTO MP 40-19(2023)
Standard Specification for Steel-Reinforced Polyethylene (PE) Ribbed Pipe, 1650- to 3000-mm (66- to 120-in.) Diameter
1650-3000mm(66-120in.)钢增强聚乙烯(PE)带肋管标准规范直径
现行
ASTM F2720/F2720M-20
Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe
玻璃纤维增强聚乙烯(PE-GF)螺旋缠绕大直径管的标准规范
2020-09-01
现行
ASTM F1960-24
Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
与交联聚乙烯(PEX)和高温聚乙烯(PE-RT)管一起使用的带PEX加强环的冷膨胀配件的标准规范
2024-07-01
现行
ASTM F2098-24
Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) to Metal Insert and Plastic Insert Fittings
将SDR9交联聚乙烯(PEX)管和SDR9高温聚乙烯(PE-RT)固定在金属嵌件和塑料嵌件配件上的不锈钢夹具的标准规范
2024-09-01
现行
ASTM F3347-23
Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
SDR9交联聚乙烯(PEX)管和SDR9高温聚乙烯(PE-RT)管用带工厂组装不锈钢压套的金属压插配件标准规范
2023-02-01
现行
ASTM F2159-23a
Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Crosslinked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
SDR9交联聚乙烯(PEX)管和SDR9高温聚乙烯(PE-RT)管用铜压接环或备用不锈钢夹的塑料插入配件标准规范
2023-03-01
现行
ASTM F3348-23a
Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
SDR9交联聚乙烯(PEX)管和SDR9高温聚乙烯(PE-RT)管用带工厂组装不锈钢压套的塑料压入配件的标准规范
2023-04-01
现行
ASTM F1807-23
Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
SDR9交联聚乙烯(PEX)管和SDR9高温聚乙烯(PE-RT)管用铜压接环或备用不锈钢夹的金属插入配件标准规范
2023-02-01