首页 馆藏资源 舆情信息 标准服务 科研活动 关于我们
现行 ASTM C1135-19(2024)
到馆提醒
收藏跟踪
购买正版
Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants 测定结构密封剂的拉伸粘合性能的标准试验方法
发布日期: 2024-05-01
1.1 本试验方法涵盖了定量测量结构密封剂(以下简称“密封剂”)拉伸粘合性能的实验室程序 1.2 以SI(公制)单位表示的数值应视为标准。括号中给出的英寸磅值仅供参考。 1.3 本标准并不旨在解决与其使用相关的所有安全问题(如有)。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践,并确定监管限制的适用性。 注1: 已知有两个ISO标准开发了类似的信息 C1135 ; ISO 8339和ISO 8340。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ====意义和用途====== 4.1 通常,玻璃或其他玻璃或面板材料在结构上用密封剂粘附到金属框架系统上。用于这些应用的密封剂旨在提供玻璃或面板与框架系统之间的结构连接。 4.2 尽管本试验方法是在一个规定的环境条件下进行的,但也可以采用其他环境条件和持续时间循环。
1.1 This test method covers a laboratory procedure for quantitatively measuring the tensile adhesion properties of structural sealants, hereinafter referred to as the “sealant.” 1.2 The values stated in SI (metric) units are to be regarded as the standard. The inch-pound values given in parentheses are provided for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: Two ISO standards are known that develop similar information to C1135 ; ISO 8339 and ISO 8340. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 Frequently, glass or other glazing or panel materials are structurally adhered with a sealant to a metal framing system. The sealants used for these applications are designed to provide a structural link between the glazing or panel and the framing system. 4.2 Although this test method is conducted at one prescribed environmental condition, other environmental conditions and duration cycles can be employed.
分类信息
关联关系
研制信息
归口单位: C24.30
相似标准/计划/法规
现行
ASTM D897-08(2024)
Standard Test Method for Tensile Properties of Adhesive Bonds
粘合剂拉伸性能的标准试验方法
2024-09-01
现行
ASTM D1623-17(2023)
Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics
硬质泡沫塑料的拉伸和拉伸粘合性能的标准试验方法
2023-05-01
现行
ASTM D6637/D6637M-15(2023)
Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method
用单肋或多肋拉伸法测定土工格栅拉伸性能的标准试验方法
2023-11-15
现行
ASTM C1382-16(2023)
Standard Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints
用于外部绝缘和表面处理系统(EIFS)接头的密封剂拉伸粘合性能测定的标准试验方法
2023-01-01
现行
GOST R ISO 11003-2-2017
Клеи. Определение свойств конструкционных клеев при сдвиге. Часть 2. Метод испытания на растяжение металлических образцов, склеенных внахлестку
粘合剂 结构胶粘剂剪切性能的测定 第二部分 用厚粘合物作金属标准的拉伸试验方法
现行
ASTM D6693/D6693M-20(2024)
Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes
非增强聚乙烯和非增强型柔性聚丙烯土工膜的拉伸性能测定标准试验方法
2024-11-01
现行
ASTM C1523-17
Standard Test Method for Determining Modulus, Tear and Adhesion Properties of Precured Elastomeric Joint Sealants
用于确定预制弹性接头密封胶的模量 撕裂和粘合性能的标准测试方法
2017-06-01
现行
ASTM D7556-10(2019)
Standard Test Methods for Determining Small-Strain Tensile Properties of Geogrids and Geotextiles by In-Air Cyclic Tension Tests
用空气循环拉伸试验测定土工格栅和土工织物的小应变拉伸性能的标准试验方法
2019-04-01
现行
ASTM C1265-22
Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
结构玻璃应用用中空玻璃边缘密封件拉伸性能测定的标准试验方法
2022-06-01
现行
ASTM D7565/D7565M-10(2017)
Standard Test Method for Determining Tensile Properties of Fiber Reinforced Polymer Matrix Composites Used for Strengthening of Civil Structures
用于确定用于加固土木结构的纤维增强聚合物基体复合材料的拉伸性能的标准试验方法
2017-01-01