1.1 本规程旨在确定在标准夹具中测量的气溶胶泡沫密封剂的漏气率。本实施规程提供了试验装置的准备程序，并进一步描述了在进行试验方法之前，将气溶胶泡沫密封剂和其他填缝料应用于试验装置 E283年 . 1.2 本规程允许测试实验室使用测试方法量化气溶胶泡沫密封剂或接缝填充产品的漏气率 E283年 并以L/（s）报告数据 · m 2. )根据实践 E29年 . 1.3 本规程与试验方法一起使用 E283年 . 尽管试验方法 E283年 是一种用于门窗产品的实验室测试方法，有兴趣对安装的装置进行现场漏气测试的个人应参考测试方法 E783 和AAMA 502。 1.4 气溶胶泡沫密封剂用于各种最终用途，通常用于减少建筑围护结构中的空气泄漏。 1.5 绝缘型材料也适用于本规程的评估。 1.6 没有其他已知实践或测试方法规定用于确定间隙填充密封剂、干燥预制泡沫或绝缘材料的漏气率的组件的制备。 1.7 以国际单位制表示的数值应视为标准值。国际单位制后括号中给出的值仅供参考，不被视为标准值。 1.8 本标准并非旨在解决与其使用相关的所有安全问题（如有）。 本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.9 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 本规程旨在测量通过用于填充建筑施工接缝的材料的气流。 5.2 本规程并不旨在建立选择空气屏障组件所需的所有标准。因此，结果仅用于比较目的，不应被视为等同于现场安装的建筑系统。

1.1 This practice is intended to determine the air leakage rate of aerosol foam sealants as measured in a standardized jig. This practice provides a procedure for preparing the test apparatus and further describes the application of aerosol foam sealant and other joint fillers to the apparatus prior to conducting Test Method E283 . 1.2 This practice allows testing laboratories to quantify the air leakage rate of aerosol foam sealants or joint filling products using Test Method E283 and reporting the data in L/(s · m 2 ) according to Practice E29 . 1.3 This practice is used in conjunction with Test Method E283 . Although Test Method E283 is a laboratory test method used with fenestration products, individuals interested in performing field air leakage tests on installed units should reference Test Method E783 and AAMA 502. 1.4 Aerosol foam sealants are used for a variety of end use applications generally intended to reduce air leakage in the building envelope. 1.5 Insulating type materials also will be found suitable for evaluation with this practice. 1.6 There are no other known practices or test methods that specify the preparation of the assemblies used to determine the air leakage rate of gap filling sealants, dry preformed foams or insulations. 1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This practice is intended to measure air flow through materials used to fill joints found in building construction. 5.2 This practice does not purport to establish all required criteria for the selection of an air barrier assembly. Therefore, the results should be used only for comparison purposes and should not be seen as the equivalent to field installed building systems.