1.1 本试验方法包括测量涂覆在光滑、有纹理或弯曲的木材或木质产品刚性基材上的涂层的干膜厚度。 1.2 本试验方法包括用于干膜厚度微观测量的木材或木质试样的制备。 1.3 该试验方法建议使用显微镜测量来分析木材或木质产品涂层的干膜厚度。 1.4 以国际单位制或英寸磅单位表示的数值应单独视为标准。每个系统中规定的值不一定是完全相等的； 因此，为了确保符合标准，每个系统应独立使用，并且不得将两个系统的值组合使用。 1.5 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.6 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ====意义和用途====== 5.1 作为干膜厚度测量仪器校准调整或精度验证的基础。 5.2 书面产品保证中规定了木材或木质产品涂层的干膜厚度，以确保木材或木质制品涂层具有适当的装饰和保护性能。 5.3 涂料公司建议涂料的最小和最大干膜厚度，以使木材或木质产品具有令人满意的装饰和保护性能。 5.4 木材或木材上涂层的平均干膜厚度- 基材料可以被制造公司用来估计所施加的涂层的理论成本。 5.5 纹理产品的最小干膜厚度与最大干膜厚度之比用作涂层均匀性的指示。 5.6 特定的涂层产品要求可能决定要进行的某些膜厚度测定。买方和卖方之间的协议可能是可取的，以适应相对于干膜厚度的产品需求。

1.1 This test method covers the measurement of dry film thickness of coatings applied to a smooth, textured or curved rigid substrate of wood or a wood-based product. 1.2 This test method covers the preparation of wood or wood-based specimens for the purpose of microscopic measurement of dry film thickness. 1.3 This test method suggests an analysis of dry film thickness of coatings on wood or wood-based products using a microscopic measurement. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 As a base for calibration adjustment or accuracy verification of dry film coating thickness measuring instruments. 5.2 The dry film thickness of coatings on wood or wood-based products is specified in written product warranties for proper decorative and protective performance of coatings on wood or wood-based products. 5.3 The minimum and maximum dry film thickness of coatings is recommended by coating companies for satisfactory decorative and protective performance on wood or wood-based products. 5.4 The average dry film thickness of coatings on wood or wood-based material may be used by manufacturing companies to estimate the theoretical cost of applied coatings. 5.5 The ratio of minimum to maximum dry film thickness on textured products is used as an indication of coating uniformity. 5.6 Specific coated product requirements may dictate certain film thickness determinations to be made. Agreement between buyer and seller may be advisable to accommodate product needs relative to dry film thickness.