请注意:此版本的所有临时修订版将在您购买时提供。用于标称乙醇浓度高达85%（E0-E85）的汽油和汽油/乙醇混合物的电动分配装置UL 87A1范围1。1这些要求适用于额定电压为600 V ac或更低的电动分配装置，用于发动机燃料。这些要求中定义的汽车燃料包括1.2.1.2中所述的一种或多种燃料。这些要求中包含的分配装置用于以下一种或多种情况: a） 根据ASTM D4814《汽车火花点火燃料标准规范》配制的汽油；b） 标称乙醇浓度不超过25%乙醇（E25）的汽油/乙醇混合物，包括按照ASTM D4814《汽车火花点火燃料标准规范》配制的汽油，当与变性燃料乙醇混合时，其配方应符合ASTM D4806《作为汽车火花点火发动机燃料与汽油混合用变性燃料乙醇的标准规范》； orc）标称乙醇浓度超过25%的汽油/乙醇混合物，按照（b）项中的标准规范配制，或按照适用的ASTM D5798《柔性燃料汽车火花点火式发动机乙醇燃料混合物标准规范》配制。1.3加油装置的安装和使用要求包含在《汽车燃油加油设施和修理库规范》、ANSI/NFPA 30A和《国家电气规范》中，ANSI/NFPA 70.1.4当设备直接位于分配装置外壳上或外壳内时，这些要求适用于用于安装或互连此类控制设备的布线方法。 1.5这些要求不适用于可能授权、监控或中断电动分配装置操作的控制设备，也不适用于其他辅助设备。这些产品将包含在与易燃液体分配装置一起使用的控制设备标准UL 1238.1.6中。这些要求不包括与柴油、生物柴油、柴油/生物柴油混合燃料、燃油或煤油一起使用的分配装置，柴油、生物柴油、，标称生物柴油浓度高达20%（B20）的柴油/生物柴油混合物，煤油和燃油，UL 87B。 1.7这些要求不包括与液化石油气一起使用的分配装置，其包含在《液化石油气电动分配装置标准》（UL 495）中。

Please note: All interim revisions for this edition available at time of your purchase will be included.Power-Operated Dispensing Devices for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85)UL 87A1 Scope1.1 These requirements apply to power-operated dispensing devices, rated 600 V ac or less, for use with motor fuels. Motor fuels, as defined by these requirements, include one or more of the fuels described in 1.2.1.2 Dispensing devices covered by these requirements are intended for use with one or more of the following:a) Gasoline formulated in accordance with the Standard Specification for Automotive Spark-Ignition Fuel, ASTM D4814;b) Gasoline/ethanol blends with nominal ethanol concentrations up to 25 percent ethanol (E25), consisting of gasoline formulated in accordance with the Standard Specification for Automotive Spark-Ignition Fuel, ASTM D4814, when blended with denatured fuel ethanol formulated to be consistent with the Standard Specification for Denatured Fuel Ethanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel, ASTM D4806; orc) Gasoline/ethanol blends with nominal ethanol concentrations above 25 percent formulated in accordance with the Standard Specifications in item (b) or formulated in accordance with the Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines, ASTM D5798, as applicable.1.3 Requirements for the installation and use of dispensing devices are included in the Code for Motor Fuel Dispensing Facilities and Repair Garages, ANSI/NFPA 30A, and the National Electrical Code, ANSI/NFPA 70.1.4 These requirements apply to wiring methods used to install or interconnect such control equipment when the equipment is located directly on or within the housing of the dispensing device.1.5 These requirements do not apply to control equipment that may authorize, monitor, or interrupt operation of a power-operated dispensing device, nor other auxiliary equipment. These products would be covered under the Standard for Control Equipment for Use with Flammable Liquid Dispensing Devices, UL 1238.1.6 These requirements do not cover dispensing devices for use with diesel fuel, biodiesel fuel, diesel/biodiesel fuel blends, fuel oil, or kerosene, which are covered in the Standard for Power-Operated Dispensing Devices for Diesel Fuel, Biodiesel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene and Fuel Oil, UL 87B.1.7 These requirements do not cover dispensing devices for use with LP-Gas, which are covered under the Standard for Power-Operated Dispensing Devices for LP-Gas, UL 495.