请注意:此版本的所有临时修订版将在您购买时提供。范围1。1.本标准包含无交错绝缘变压器中使用的单层和多层绝缘绕组线的要求；以及根据信息技术设备标准-安全-第1部分:一般要求，UL 60950-1，医疗电气设备标准，第1部分:一般安全要求，UL 60601使用的无交错绝缘的固体绝缘和绝缘绕组线- IEC 61558-1《电力变压器、电源、电抗器和类似产品的安全第1部分:一般要求和试验》。当这些要求被确定为与其他标准兼容时，这些要求并不是为了禁止在其他标准范围内的设备中使用此类绕组线。1.2本标准还包含适用于最终产品标准的漆包全绝缘线（FIW）的要求。漆包绕组线应为指定的NEMA MW 85型，如NEMA MW 1000电磁线标准所规定。 1.3这些要求包括直径在0.05毫米（0.002英寸）和5.0毫米（0.2英寸）之间的绕组线，以及直径在0.040毫米（0.0016英寸）和1.60毫米（0.06英寸）之间的MW 85溶剂基搪瓷涂层绕组线。1.4本标准涵盖的绕组线还应符合聚合材料-短期性能标准中的红外分析要求评估，UL 746A。1.5除非1.2中另有规定，否则本标准不包括溶剂基搪瓷涂层磁线。参见绝缘材料系统标准- 将军，UL 1446。如果单层和多层绝缘绕组线的预期用途高于105（A）级，则需要根据UL 1446对绝缘系统进行额外测试。

Please note: All interim revisions for this edition available at time of your purchase will be included.Scope1.1 This Standard contains requirements for single and multi - layer insulated winding wire used in transformers without interleaved insulation; and solid insulation and insulated winding wire without interleaved insulation intended for use in accordance with the Standard for Information Technology Equipment - Safety - Part 1: General Requirements, UL 60950-1, the Standard for Medical Electrical Equipment, Part 1: General Requirements for Safety, UL 60601-1, or the Safety of Power Transformers, Power Supplies, Reactors and Similar Products - Part 1: General Requirements and Tests, IEC 61558-1. These requirements are not intended to prohibit use of this type of winding wire in equipment covered by the scope of other standards when these requirements are determined to be compatible with those standards.1.2 This Standard also contains requirements for enamelled Fully-Insulated Wire (FIW) that are deemed suitable for use in end-products standards. The enamelled winding wire shall be a designated NEMA Type MW 85 as specified in the Standard for Magnet Wire, NEMA MW 1000.1.3 These requirements cover winding wires with a diameter between 0.05 mm (0.002 in) and 5.0 mm (0.2 in) and MW 85 solvent-based enamel coated winding wires with a diameter between 0.040 mm (0.0016 in) and 1.60 mm (0.06 in).1.4 The winding wire covered by this Standard shall also comply with the infrared analysis requirements in the Standard for Polymeric Materials - Short Term Property Evaluations, UL 746A.1.5 This Standard does not cover solvent-based enamel coated magnet wire unless as specified in 1.2. See the Standard for Systems of Insulating Materials - General, UL 1446. If the desired usage of the single- and multi-layer Insulated winding wire is above Class 105 (A), additional testing of the insulation system would be required in accordance with UL 1446.