1.1 本试验方法为确定深波纹结构钢板中螺栓纵向搭接接缝的接缝强度提供了一种综合方法。试验方法包括实验室试验程序，该程序规定了试样制备、试验设备和数据收集。试验方法还包括根据试验结果计算接缝强度的方法。本标准试验方法适用于实际提供的螺栓接缝极限强度的波纹钢结构 A796/A796M . 1.2 单位- 以英寸-磅为单位的数值应视为标准值。 1.3 本标准并非旨在解决与其使用相关的所有安全问题（如有）。 本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 本试验方法提供了一种测试程序，以确定深波纹结构板中具有搭接连接的螺栓纵向接缝的极限抗压强度。 本试验方法适用于相邻板之间具有周向接缝的可变长度纵向接缝。 注1: 该测试旨在测试实际中具有以下波纹尺寸的板中的螺栓纵向接缝 A796/A796M :15英寸。5.5。在里面（实践 A796/A796M 表34和35），20英寸。9.5英寸。（实践 A796/A796M 表36和37）和16 in。6英寸。（实践 A796/A796M 表38和39）。 5.2 本试验中获得的最大载荷以及本试验方法中的归一化程序用于确定螺栓连接结构板纵向接缝的极限强度值，以便根据实践进行设计 A796/A796M .

1.1 This test method provides a comprehensive method for determining the seam strength for bolted longitudinal lapped seams in deep corrugated structural steel plate. The test method includes a laboratory test procedure which specifies specimen preparation, test equipment, and data collection. The test method also includes a method to calculate seam strength from the test results. This standard test method is applicable to corrugated steel structures with ultimate strength of bolted seams provided in Practice A796/A796M . 1.2 Units— The values stated in inch-pound units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This test method provides a procedure for testing to determine the ultimate strength in compression of bolted longitudinal seams with lapped connections in deep corrugated structural plate. This test method is applicable to variable length longitudinal seams with circumferential seams between adjacent plates. Note 1: The testing is intended for bolted longitudinal seams in plate with the following corrugation sizes in Practice A796/A796M : 15 in. by 5.5. in. (Practice A796/A796M Tables 34 and 35), 20 in. by 9.5 in. (Practice A796/A796M Tables 36 and 37), and 16 in. by 6 in. (Practice A796/A796M Table 38 and 39). 5.2 The maximum load achieved in this testing, along with normalization procedures in this test method, are used to establish values for ultimate strength of bolted structural plate longitudinal seams for design in accordance with Practice A796/A796M .