IEC 61010-2-030:2023规定了具有测试或测量电路的设备的安全要求，这些电路出于测试或测量目的连接到测量设备本身之外的设备或电路。这些包括作为电气测试和测量设备、实验室设备或过程控制设备一部分的测量电路。设备中的这些电路在电路和操作员之间具有附加的保护装置。这第三版取消并取代了2017年出版的第二版。本版构成技术修订版。与上一版相比，此版本包括以下重大技术变更: a)在1.2.1中，在范围中增加了防止读取电压可能发生的危险的要求；b)第2条，所有规范性引用均已注明日期，并增加了新的规范性引用； c)在4.3.2.5中，对电源的要求进行了修改； d)在4.3.2.6中，对输入/输出的要求进行了修改； e)在4.4.2.101中，增加了关于电涌保护装置的新子条款； f)在5.1.5.101.2中，要求测量端子电压的最低额定值； g)子条款6.6.101修改了先前版本的6.6.101和6.6.102: 1）在6.6.101.1中，可以允许使用I组绝缘材料来确定测量电路端子的爬电距离； 2）在6.6.101.2中，定义了测量未配合位置电路端子的间隙和爬电距离，最高可达3 000 V； 3）在6.6.101.3中，已经规定了在部分配合位置测量电路端子的要求；4）在6.6.101.4中，规定了在配合位置测量电路端子的要求； 5）子条款6.6.101.5取代6.6.102； h)增加了9.101子条款，以考虑保护测量电路免受火灾和电弧闪光的蔓延，表102已被表K.101取代； i)在9.101.2中，对先前版本101.3的重新定位； j)在9.101.3中，上一版101.4的重新定位，扩展到测量类别II，并参考IEC 61000-4-5进行测试； k)在14.101中，删除了上一版14.102和14.101的重新定位； l)在101.3中，对先前版本的101.5进行了重新定位，并增加了针对读取电压值引起的危险的更多要求； m)在K.2.1中，提出了另一种确定二次回路间隙的方法；n）在K.3.2中，用于清除率计算的新表K.15和表K.16； o)在K.101.4.1中，新的表K.103和表K.104替换表K.102、表K.103和表K.104； p)在K.101.4中，该子条款已被审查；固体绝缘的表格和测试已经修改；表K.105取代表K.9； q)表K.101，替换表K.106； r)条款K.4，该条款的重新起草，以提出一种确定降低瞬态过电压的电路的Ut的方法； s)附件AA:重新设计了图AA.1； t)附件EE:增加了一个新的信息性附件，用于确定表101的清除量。 根据IEC指南104，它具有团体安全出版物的地位。

IEC 61010-2-030:2023 specifies safety requirements for equipment having testing or measuring circuits which are connected for test or measurement purposes to devices or circuits outside the measurement equipment itself. These include measuring circuits which are part of electrical test and measurement equipment, laboratory equipment, or process control equipment. These circuits in equipment have additional protective means between the circuit and an operator. This third edition cancels and replaces the second edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) in 1.2.1, requirements for protection against hazards which could occur from reading a voltage have been added to the scope;
b) Clause 2, all normative references have been dated and new normative references have been added;
c) in 4.3.2.5, requirements for power supply have been modified;
d) in 4.3.2.6, requirements for inputs/outputs have been modified;
e) in 4.4.2.101, a new subclause about surge protective devices has been added;
f) in 5.1.5.101.2, minimum ratings for voltage of measuring terminals are required;
g) Subclause 6.6.101 modifies 6.6.101 and 6.6.102 of previous edition:
1) in 6.6.101.1, insulating material of group I may be allowed for determination of creepage distances of measuring circuit terminals;
2) In 6.6.101.2, clearances and creepage distances up to 3 000 V for measuring circuit terminals in unmated position have been defined;
3) in 6.6.101.3, requirements for measuring circuit terminals in partially mated position have been specified;
4) in 6.6.101.4, requirements for measuring circuit terminals in mated position have been specified;
5) Subclause 6.6.101.5 replaces 6.6.102;
h) Subclause 9.101 to consider the protection of measuring circuits against the spread of fire and arc flash has been added and Table 102 has been replaced by Table K.101;
i) in 9.101.2, relocation of 101.3 of previous edition;
j) in 9.101.3, relocation of 101.4 of previous edition, extension to measurement category II and reference to IEC 61000-4-5 for tests;
k) in 14.101, relocation of 14.102 and 14.101 of previous edition has been removed;
l) in 101.3, relocation of 101.5 of previous edition, and more requirements added against hazard occurring from reading a voltage value;
m) in K.2.1, another method for determination of clearances of secondary circuits is proposed;
n) in K.3.2, new Table K.15 and Table K.16 for clearance calculation;
o) in K.101.4.1, new Table K.103 and Table K.104 replace Table K.102, Table K.103 and Table K.104;
p) in K.101.4, the subclause has been reviewed; Tables and tests for solid insulation have been modified; Table K.105 replaces Table K.9;
q) Table K.101, replacement of Table K.106;
r) Clause K.4, redraft of the clause to propose a method for determination of Ut for circuits which reduce transient overvoltages;
s) Annex AA: Figure AA.1 has been redesigned;
t) Annex EE: addition of a new informative annex for determination of clearances for Table 101.
It has the status of a group safety publication in accordance with IEC Guide 104.