1.1 本规程描述了用于评估安全气囊模块和模块部件在展开过程中和展开后的物理性能的程序和条件。 1.2 通过本实践可获得的物理性能特征包括由仪器确定的内部缓冲压力、由高速摄影确定的缓冲几何形状以及由目视检查确定的材料完整性。 1.3 本规程适用于驾驶员侧和乘客侧安全气囊模块。 1.4 除本实施规程中规定的程序和仪器外，买方和供应商可通过协议使用，具体偏差应在报告中确认。 1.5 以国际单位制或英寸-磅单位表示的数值应单独视为标准值。每个系统中规定的值不是精确的等价物；因此，每个系统必须相互独立使用。 1.6 本标准并非旨在解决与其使用相关的所有安全问题（如有）。 本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.7 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 本规程旨在作为安全气囊重复测试、安全测试和准确数据收集的一般指南。 5.2 买方和供应商可使用本规程建立标准，供应商将根据该标准测试安全气囊模块，以确定是否可以将大量材料运输给买方。 5.3 除非买方和供应商之间的协议另有规定，否则本规程应构成展开安全气囊模块进行测试的测试条件、程序和设备。 其旨在作为买方和供应商之间建立书面材料规范或等效协议的指南。当（基于经验）考虑到织物性能、材料处理设备或安全气囊系统设计另有规定时，本规范可能会偏离本文所述惯例。

1.1 This practice describes the procedures and conditions used to evaluate the physical performance of inflatable restraint modules and module components during and after deployment. 1.2 The physical performance characteristics that may be obtained by this practice are internal cushion pressures determined by instrumentation, cushion geometries determined by high-speed photography, and material integrity determined by visual inspection. 1.3 This practice is applicable to driver and passenger side inflatable restraint modules. 1.4 Procedures and apparatus other than those stated in this practice may be used by agreement between the purchaser and the supplier with the specific deviations from the practice acknowledged in the report. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This practice is intended to be a general guideline for repetitive testing, safe conduct of tests, and accurate data collection for inflatable restraints. 5.2 This practice may be used by the purchaser and the supplier to establish the criteria by which inflatable restraint modules will be tested by the supplier to determine whether a lot of material is acceptable for shipment to the purchaser. 5.3 Unless otherwise specified by agreement between the purchaser and the supplier, this practice shall constitute the test conditions, procedures, and equipment by which inflatable restraint modules are deployed for testing. It is intended to be used as a guideline in establishing a written material specification or equivalent agreement between the purchaser and the supplier. The specification may deviate from the practices described herein when (based on experience) considerations of fabric properties, material handling equipment, or inflatable restraint system design dictate otherwise.