请注意:此版本的所有临时修订版将在您购买时提供。柴油、生物柴油、标称生物柴油浓度不超过20%（B20）的柴油/生物柴油混合物、煤油和燃油UL 87B1范围1的电动分配装置标准。1这些要求适用于额定电压为600 V ac或更低的动力分配装置，用于燃料。这些要求中定义的燃料包括1.2.1.2中描述的一种或多种燃料。这些要求中包含的分配装置用于以下一种或多种燃料:a）根据柴油标准规范配制的标称生物柴油浓度不超过5%（B0-B5）的柴油和柴油/生物柴油混合物，ASTM D975。 b） 标称生物柴油浓度在5%到20%之间（B6-B20）的柴油/生物柴油混合物，按照ASTM D7467《柴油、生物柴油混合物（B6-B20）标准规范》配制。c） 生物柴油（B99.9/B100）按照ASTM D6751《中间馏分燃料用生物柴油混合油（B100）标准规范》配制。d） 根据煤油标准规范ANSI/ASTM D3699配制的煤油。e） 根据ASTM D396燃油标准规范配制的燃油（加热油）。1.3加注装置的安装和使用要求包含在《汽车燃油加注设施和修理库规范》（ANSI/NFPA 30A）和《国家电气规范》（ANSI/NFPA 70）中。 1.4当设备直接位于分配装置外壳上或外壳内时，这些要求适用于用于安装或互连此类控制设备的布线方法。1.5这些要求不适用于可能授权、监控或中断电动分配装置操作的控制设备，也不适用于其他辅助设备。这些产品将包含在UL 1238.1.6《易燃液体分配装置控制设备标准》中。这些要求不包括用于任何浓度汽油或汽油/乙醇混合物的分配装置。这些分配装置包含在汽油和汽油/乙醇混合物的电动分配装置标准中，标称乙醇浓度高达85%（E0- E85），UL 87A。1.7这些要求不包括用于液化石油气的分配装置，其包含在《液化石油气电动分配装置标准》UL 495.1.8中。这些要求不包括用于生物柴油浓度在B20和B99之间的柴油/生物柴油混合物的设备。9/B100。

Please note: All interim revisions for this edition available at time of your purchase will be included.Standard for Power-Operated Dispensing Devices for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel OilUL 87B1 Scope1.1 These requirements apply to power-operated dispensing devices, rated 600 V ac or less, for use with fuels. Fuels, as defined by these requirements, include one or more of the fuels described in 1.2.1.2 Dispensing devices covered by these requirements are intended for use with one or more of the following:a) Diesel fuel and diesel fuel/biodiesel blends with nominal biodiesel concentrations up to 5 percent (B0 - B5) formulated in accordance with the Standard Specification for Diesel Fuel Oils, ASTM D975.b) Diesel/biodiesel blends with nominal biodiesel concentrations from 5 percent up to 20 percent (B6 - B20) formulated in accordance with the Standard Specification for Diesel Fuel Oil, Biodiesel Blends (B6 - B20), ASTM D7467.c) Biodiesel (B99.9/B100) formulated in accordance with the Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels, ASTM D6751.d) Kerosene formulated in accordance with the Standard Specification for Kerosine, ANSI/ASTM D3699.e) Fuel Oil (heating oil) formulated in accordance with the Standard Specification for Fuel Oils, ASTM D396.1.3 Requirements for the installation and use of dispensing devices are included in the Code for Motor Fuel Dispensing Facilities and Repair Garages, ANSI/NFPA 30A, and the National Electrical Code, ANSI/NFPA 70.1.4 These requirements apply to wiring methods used to install or interconnect such control equipment when the equipment is located directly on or within the housing of the dispensing device.1.5 These requirements do not apply to control equipment that may authorize, monitor, or interrupt operation of a power-operated dispensing device, nor other auxiliary equipment. These products would be covered under the Standard for Control Equipment for Use with Flammable Liquid Dispensing Devices, UL 1238.1.6 These requirements do not cover dispensing devices for use with gasoline or gasoline/ethanol blends of any concentration. These dispensing devices are covered under the Standard for Power-Operated Dispensing Devices for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 - E85), UL 87A.1.7 These requirements do not cover dispensing devices for use with LP-Gas, which are covered under the Standard for Power-Operated Dispensing Devices for LP-Gas, UL 495.1.8 These requirements do not cover equipment intended for diesel/biodiesel blends with a biodiesel concentration between B20 and B99.9/B100.