本文件规定了在10°C至35°C的环境温度范围内测试时，由耐腐蚀不锈钢制成的粗螺距螺纹和细螺距螺纹的螺栓、螺钉和螺柱的机械和物理性能。它规定了紧固件用奥氏体、马氏体、铁素体和双相（奥氏体-铁素体）钢种的性能等级。 当螺栓、螺钉和螺柱一起考虑时，在本文件中使用术语“紧固件”。 ISO 3506？图6提供了关于合适的不锈钢及其性能的一般规则和附加技术信息。 符合本文件要求的紧固件在第1段规定的环境温度下进行评估。在高温和/或低温下，它们可能不保持规定的机械和物理性能。注1:符合本文件要求的紧固件不受限制地用于以下范围的应用？20℃至+150℃；然而，符合本文件的紧固件也用于此范围之外的应用，低至？196°C至+300°C。更多细节见附录A和ISO 3506？6. 在的温度范围之外？20°C至+150°C，用户有责任与有经验的紧固件冶金学家协商，并考虑例如不锈钢成分、暴露在高温或低温下的持续时间、温度对紧固件机械性能和夹紧部件的影响以及螺栓接头的腐蚀性使用环境，确定给定应用的适当选择。 注2 ISO 3506？5是为了帮助选择在高达+800℃的温度下使用的适当不锈钢等级和性能等级而开发的。本文件适用于螺栓、螺钉和螺柱: -采用符合ISO 68的ISO公制螺纹？1, -具有符合ISO 261和ISO 262的直径/节距组合， -具有粗螺距螺纹M1、6至M39和细螺距螺纹M8 × 1至M39 × 3， -螺纹公差符合ISO 965？1和ISO 965？2, -具有指定的属性类，以及 -任何形状。 不锈钢等级和性能等级可用于本文件直径限制之外的尺寸（即d<1.6 mm或d>39 mm），前提是满足所有适用的化学、机械和物理要求。 某些螺栓、螺钉和螺柱可能由于其头部或无螺纹柄的几何形状而无法满足本文件的拉伸或扭转要求，从而导致负载能力降低（例如。g.当头部中的剪切面积小于螺纹中的应力面积时；参见8.2.2)。 本文件不适用于不处于拉伸应力下的固定螺钉和类似螺纹紧固件（参见ISO 3506？3）。 它没有指定功能属性的要求，例如: -扭矩/夹紧力特性， -剪切强度， -抗疲劳性，或 -可焊性。

This document specifies the mechanical and physical properties of bolts, screws and studs, with coarse pitch thread and fine pitch thread, made of corrosion-resistant stainless steels, when tested at the ambient temperature range of 10 °C to 35 °C. It specifies property classes in relation to austenitic, martensitic, ferritic and duplex (austenitic-ferritic) steel grades for fasteners. The term "fasteners" is used in this document when bolts, screws and studs are considered all together. ISO 3506？6 provides general rules and additional technical information on suitable stainless steels and their properties. Fasteners conforming to the requirements of this document are evaluated at the ambient temperature specified in paragraph 1. It is possible that they do not retain the specified mechanical and physical properties at elevated and/or lower temperatures. NOTE 1 Fasteners conforming to the requirements of this document are used without restriction in applications ranging from?20 °C to +150 °C; however, fasteners conforming to this document are also used for applications outside this range down to?196 °C and up to +300 °C. For more details, see Annex A and ISO 3506？6. Outside the temperature range of?20 °C to +150 °C, it is the responsibility of the user to determine the appropriate choice for a given application in consultation with an experienced fastener metallurgist and by taking into account e.g. stainless steel composition, duration of exposure at elevated or low temperature, the effect of the temperature on the fasteners mechanical properties and clamped parts, and the corrosive service environment of the bolted joint. NOTE 2 ISO 3506？5 is developed in order to assist in the selection of appropriate stainless steel grades and property classes intended for use at temperatures up to +800 °C. This document applies to bolts, screws and studs: — with ISO metric thread in accordance with ISO 68？1, — with diameter/pitch combinations in accordance with ISO 261 and ISO 262, — with coarse pitch thread M1,6 to M39, and fine pitch thread M8×1 to M39×3, — with thread tolerances in accordance with ISO 965？1 and ISO 965？2, — with specified property classes, and — of any shape. Stainless steel grades and property classes can be used for sizes outside the diameter limits of this document (i.e. for d < 1,6 mm or d > 39 mm), provided that all applicable chemical, mechanical and physical requirements are met. Certain bolts, screws and studs might not fulfil the tensile or torsional requirements of this document because of the geometry of their head or unthreaded shank, thus resulting in reduced loadability (e.g. when shear area in the head is less than the stress area in the thread; see 8.2.2). This document does not apply to set screws and similar threaded fasteners not under tensile stress (see ISO 3506？3). It does not specify requirements for functional properties such as: — torque/clamp force properties, — shear strength, — fatigue resistance, or — weldability.