请注意:此版本的所有临时修订版将在您购买时提供。这些要求适用于根据以下标准进行便携式或永久性安装的有机发光二极管（OLED）面板，以及与发电机、电池、燃料电池、太阳能电池等隔离（非公用设施连接）电源的连接:在加拿大:加拿大电气规范，第一部分，电气安装安全标准，CSA C22。在美国:国家电气规范（NEC），ANSI/NFPA 70。 本标准涵盖的OLED面板仅安装在干燥或潮湿的位置，采用以下一种或多种配置:a）直接固定在结构的墙壁或天花板上，b）集成到机械框架或结构中，机械框架或结构依次安装或固定在结构的墙壁或天花板上（例如，灯具或标志），c） 集成到便携式机械框架或结构中，无需特殊工具或技能（例如，便携式灯具）即可重新定位。本标准涵盖的OLED面板拟由在电气结构规定的电压和电流限制范围内工作的电源供电- 总则，第12节。这些电压限值被理解为不存在电击伤害的风险，而电流限值足以充分降低引发火灾的风险。对于超出第12节限值的电源供应的OLED面板，请参阅更大功率OLED面板的补充要求，附录a.根据1.2（b）或（c）安装在固定式或便携式灯具框架结构内的OLED面板无需符合本标准的要求，其中适用灯具标准充分解决了火灾或伤害风险。 这些要求不涉及用于为OLED面板供电的电源。应评估包括OLED面板和电源的机械集成组件是否符合适用的灯具标准。一些适用于OLED面板的电源在《电气结构-概述》第12节中进行了说明。本标准不包括用于以下用途的OLED面板的评估要求: 在加拿大:a）加拿大电气规范CSA C22中规定的危险场所。 1.b） 《加拿大电气规范》CSA C22第24节定义的普通患者护理区或重症患者护理区。1.c） 加拿大电气规范CSA C22第46节定义的应急系统。1.ord）加拿大电气规范CSA C22第12-010条规定的空气处理空间。1.在美国:a）国家电气规范（NEC）、ANSI/NFPA 70中规定的危险场所；b） 《国家电气规范》（NEC）ANSI/NFPA 70第517条定义的普通患者护理区或重症患者护理区； c） 国家电气规范（NEC）第700条ANSI/NFPA 70规定的应急系统；或 d） 国家电气规范（NEC）第300.22（C）条ANSI/NFPA 70规定的空气处理空间。 1.7本标准不包括评估OLED面板是否符合建筑规范抗震要求的要求。

Please note: All interim revisions for this edition available at time of your purchase will be included.These requirements apply to organic lighting emitting diode (OLED) panels intended for portable or permanent installation in accordance with the following standards, and for connection to isolated (non-utility connected) power sources such as generators, batteries, fuel cells, solar cells, and the like:In Canada:Canadian Electrical Code, Part I, Safety Standard for Electrical Installations, CSA C22.1,In the United States:National Electrical Code (NEC), ANSI/NFPA 70.The OLED panels covered by this standard are intended to be installed in dry or damp locations only, in one or more of the following configurations:a) Secured directly to the walls or ceiling of a structure,b) Integrated into a mechanical frame or structure that is in turn mounted or secured to the walls or ceiling of a structure (for example, a luminaire or sign),c) Integrated into a mechanical frame or structure that is portable and able to be relocated without special tools or skills (for example, a portable luminaire).The OLED panels covered by this standard are intended to be supplied from an electrical power source operating within the voltage and current limits specified in Electrical Construction - General, Section 12. These voltage limits are understood to represent no risk of electric shock injury, and the current limits sufficient to adequately reduce the risk of fire initiation.For OLED panels intended to be supplied by a power source beyond the limits of Section 12, see the Supplemental Requirements for Higher Power OLED Panels, Annex a.An OLED panel mounted within the frame structure of a fixed or portable luminaire per 1.2 (b) or (c) need not comply with the requirements in this standard where the risk of fire or injury is fully addressed by the applicable luminaire standard.These requirements do not address the power sources used to supply an OLED panel. Mechanically integrated assemblies that include both an OLED panel and a power source shall be evaluated for conformance with the applicable luminaire standard. Some power sources suitable for use with OLED panels are identified in Electrical Construction - General, Section 12.This standard does not include requirements for the evaluation of OLED panels intended for use in: In Canada:a) Hazardous locations as specified in the Canadian Electrical Code, CSA C22.1;b) General patient care areas or critical patient care areas as defined by Section 24 of the Canadian Electrical Code, CSA C22.1;c) Emergency systems as defined by Section 46 of the Canadian Electrical Code, CSA C22.1; ord) Air-handling spaces as defined by Rule 12-010 of the Canadian Electrical Code, CSA C22.1.In the United States:a) Hazardous locations as specified in the National Electrical Code (NEC), ANSI/NFPA 70;b) General patient care areas or critical patient care areas as defined by Article 517 of the National Electrical Code (NEC), ANSI/NFPA 70; c) Emergency systems as defined by Article 700 of the National Electrical Code (NEC), ANSI/NFPA 70; or d) Air-handling spaces as defined by Article 300.22(C) of the National Electrical Code (NEC), ANSI/NFPA 70. 1.7 This standard does not include requirements for the assessment of OLED panel compliance with building code seismic requirements.