本文件建立了热塑性PE-UHMW材料的名称体系，可作为规范的基础。在本文件中，PE-UHMW材料是熔体质量流量（MFR）小于0.1g\/10min的聚乙烯材料，在190°C和21.6kg负荷下测量。注:已确认，熔体体积流量（MVR）可用于在230°C\/21,6 kg的试验条件和3628 mm的模具孔径下表征一些PE-UHMW材料（如管材）（见ISO 21304-2）。PE-UHMW的类型通过基于适当等级的设计特性的分类系统进行区分:a） 粘度值；b） 拉伸应力；c） 夏比双缺口冲击强度；以及有关预期用途和\/或加工方法、重要特性、添加剂、着色剂、填料和增强材料的信息。该命名系统适用于所有PE-UHMW均聚物和具有质量小于50%的其它1-烯烃单体含量的乙烯超高分子量共聚物和具有官能团质量的最大值为3%的非烯烃单体含量。适用于未经着色剂、填料和其他添加剂改性或改性的粉末、颗粒或颗粒形式的正常使用材料。这并不意味着具有相同名称的材料必然具有相同的性能。本文件不提供指定材料所需的工程数据、性能数据或加工条件数据。如果需要此类附加性能，则应根据ISO 21304-2中规定的试验方法（如适用）进行测定。为了指定热塑性PE-UHMW材料以满足特定规范，数据块5中给出了要求（见4.1）。

This document establishes a system of designation for thermoplastic PE-UHMW materials, which can be used as the basis for specifications. For the purposes of this document, PE-UHMW materials are polyethylene materials having a melt mass-flow rate (MFR) of less than 0,1 g/10 min, measured at 190 °C and 21,6 kg load. NOTE It has been confirmed that the melt volume-flow rate (MVR) is useful for characterizing some PE-UHMW materials (e.g. pipe materials) under the test condition of 230 °C/21,6 kg and bore diameter of die with 3,628 mm (see ISO 21304-2). The types of PE-UHMW are differentiated from each other by a classification system based on appropriate levels of the designatory properties: a) viscosity number; b) elongational stress; c) Charpy double-notched impact strength; and on information about the intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. This designation system is applicable to all PE-UHMW homopolymers and to ultra-high-molecular-weight copolymers of ethylene having a content of other 1-olefinic monomers of less than 50 % by mass and a content of non-olefinic monomers with functional groups up to a maximum of 3 % by mass. It applies to materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colorants, fillers and other additives. It is not intended to imply that materials having the same designation give necessarily the same performance. This document does not provide engineering data, performance data or data on processing conditions which can be required to specify a material. If such additional properties are required, they are intended to be determined in accordance with the test methods specified in ISO 21304-2, if suitable. In order to specify a thermoplastic PE-UHMW material to meet particular specifications, the requirements are to be given in data block 5 (see 4.1).