首页 馆藏资源 舆情信息 标准服务 科研活动 关于我们
现行 ASTM E2688-24
到馆提醒
收藏跟踪
购买正版
Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics 评估表面燃烧特性的试样制备和胶带安装的标准实施规程
发布日期: 2024-05-01
1.1 本规程涵盖了使用试验方法测试胶带以评估火焰蔓延和烟雾发展作为表面燃烧特性时样品制备和安装的程序 E84 .如试验方法所述,胶带应在应用于纤维水泥板的全覆盖范围内进行试验 E84 . 1.2 本规程适用于建筑物内各种用途的胶带。 1.3 按照测试方法进行测试 E84 . 1.4 此做法未提供可作为监管工具的合格/不合格标准。 1.5 此做法不适用于系统评估。仅用于材料的比较。 1.6 在裁判裁决中,使用以英寸-磅为单位的数值作为标准。括号中给出了国际单位制中的值,仅供参考; 看见 IEEE/atm SI-10 以了解更多详细信息。 1.7 该消防标准不能用于提供定量措施。 1.8 火灾测试具有内在的危险性。在进行这些试验时,应为人员和财产提供足够的保护。 1.9 本标准给出了试样制备和安装的说明,但试验方法中给出了火灾试验响应方法 E84 。另请参见第节 9 . 1.10 本标准的文本引用了提供解释性材料的注释和脚注。这些注释和脚注不应被视为本标准的要求。 1.11 本标准并不旨在解决与其使用相关的所有安全问题(如有)。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践,并确定监管限制的适用性。 1.12 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ====意义和用途====== 5.1 用胶带制成的建筑产品通常用于试验方法 E84 用于符合建筑、生命安全规范或机械规范要求。本规程详细描述了胶带的样品安装程序。 5.2 对于用于评估火焰蔓延和烟雾发展作为表面燃烧特性的测试带,规范通常是沉默的。 本规程描述了此类材料和产品的试样制备和安装程序。 5.3 该材料应代表实际现场安装中使用的材料。 5.4 本程序的限制是与试验方法相关的限制 E84 .
1.1 This practice covers a procedure for specimen preparation and mounting when testing tapes to assess flame spread and smoke development as surface burning characteristics using Test Method E84 . Tapes are to be tested in full coverage as applied to fiber cement board as described in Test Method E84 . 1.2 This practice applies to any tape intended for various uses within buildings. 1.3 Testing is conducted in accordance with Test Method E84 . 1.4 This practice does not provide pass/fail criteria that can be used as a regulatory tool. 1.5 This practice is not for system evaluation. It is for the comparison of the materials only. 1.6 Use the values stated in inch-pound units as the standard, in referee decisions. The values in the SI system of units are given in parentheses, for information only; see IEEE/ASTM SI-10 for further details. 1.7 This fire standard cannot be used to provide quantitative measures. 1.8 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.9 This standard gives instructions on specimen preparation and mounting, but the fire-test-response method is given in Test Method E84 . See also Section 9 . 1.10 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered requirements of the standard. 1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.12 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 Building products made with tapes are often used for applications for which Test Method E84 is used for compliance with building, life safety code or mechanical code requirements. This practice describes, in detail, specimen mounting procedures for tapes. 5.2 Codes are often silent with regard to testing tapes for the assessment of flame spread and smoke development as surface burning characteristics. This practice describes specimen preparation and mounting procedures for such materials and products. 5.3 The material shall be representative of the materials used in actual field installations. 5.4 The limitations for this procedure are those associated with Test Method E84 .
分类信息
关联关系
研制信息
归口单位: E05.22
相似标准/计划/法规
现行
ASTM E2690-22
Standard Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Characteristics
评估表面燃烧特性的填缝料和密封剂的试样制备和安装的标准实施规程
2022-11-01
现行
ASTM E2579-23b
Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics
评估表面燃烧特性的木制品样品制备和安装的标准实施规程
2023-11-01
现行
ASTM E1078-14(2020)
Standard Guide for Specimen Preparation and Mounting in Surface Analysis
标本制备和表面分析安装标准指南
2020-12-01
现行
ASTM E2573-24
Standard Practice for Specimen Preparation and Mounting of Site-Fabricated Stretch Systems to Assess Surface Burning Characteristics
评估表面燃烧特性的现场制造拉伸系统的样品制备和安装的标准实施规程
2024-05-01
现行
ASTM E2231-21
Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics
评定表面燃烧特性用管道和导管绝缘材料的试样制备和安装的标准实施规程
2021-12-15
现行
ASTM C862-16(2020)
Standard Practice for Preparing Refractory Concrete Specimens by Casting
通过铸造制备耐火混凝土样品的标准实践
2020-11-01
现行
ASTM C903-15(2020)
Standard Practice for Preparing Refractory Specimens by Cold Gunning
冷葫芦准备耐火试样的标准实践
2020-11-01
现行
ASTM D2094-00(2023)
Standard Practice for Preparation of Bar and Rod Specimens for Adhesion Tests
附着力试验用棒材和棒材试样的制备
2023-01-01
现行
ASTM G1-03(2017)e1
Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
制备“清洁”和评估腐蚀试样的标准实施规程
2017-11-01
现行
ASTM G58-85(2023)
Standard Practice for Preparation of Stress-Corrosion Test Specimens for Weldments
焊接件应力腐蚀试样制备的标准实施规程
2023-12-01
现行
ASTM D4223/D4223M-20
Standard Practices for Preparation of Test Specimens of Asphalt-Stabilized Soils
沥青稳定土试样制备的标准实施规程
2020-11-01
现行
ASTM E2988-17(2022)
Standard Practice for Specimen Preparation and Mounting of Flexible Fibrous Glass Insulation for Metal Buildings to Assess Surface Burning Characteristics
评估表面燃烧特性的金属建筑物用柔性纤维玻璃隔热材料的样品制备和安装
2022-11-01
现行
ASTM E795-23
Standard Practices for Mounting Test Specimens During Sound Absorption Tests
吸声试验期间安装试样的标准实施规程
2023-01-01
现行
KS F 2486
아스팔트 혼합물의 동탄성 계수 시험용 시편 제작 방법
动态模量试验用沥青混合料试样制备的标准实施规程
2020-12-30
现行
ASTM D6926-20
Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus
使用马歇尔设备制备沥青混合物样品的标准实践
2020-01-01
现行
ASTM C1140/C1140M-11(2019)
Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels
喷浆混凝土测试板准备和测试样品的标准实践
2019-12-15
现行
ASTM B925-15(2022)
Standard Practices for Production and Preparation of Powder Metallurgy (PM) Test Specimens
粉末冶金(PM)试样的生产和制备的标准实施规程
2022-03-01
现行
ASTM F2971-13(2021)
Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing
添加剂制造制备试样数据报告的标准实施规程
2021-07-15
现行
ASTM D4204-16(2023)
Standard Practice for Preparing Plastic Film Specimens for a Round-Robin Study
循环研究用塑料薄膜样品制备的标准实施规程
2023-11-01
现行
AASHTO PP 92-19(2022)
Standard Practice for Preparation of Test Specimens Using the Plastic Mold Compaction Device
使用塑料模具压实装置制备试样的标准规范