1.1 这是一个火灾测试响应标准。 1.2 本试验方法提供了一种方法，通过在通风良好的条件下，将试验样品（床垫或带基础的床垫）置于指定的燃烧火源下，测量特定的燃烧试验响应，来确定公共场所使用的床垫的燃烧行为。 1.3 这是床垫或带基础的床垫的测试方法。 1.4 获得的测试数据描述了在应用特定点火源后，从点火到所有燃烧停止、经过1小时或出现不可避免的闪络的燃烧行为。 1.5 除本试验方法规定的情况外，本试验方法不提供床垫在火灾条件下的防火性能信息。特别是，本试验方法不适用于香烟阴燃点燃。看见 5.12 了解更多信息。 1.6 通过耗氧法测量燃烧试样的热释放速率。看见 5.12.4 了解更多信息。 1.7 其他测量是产生的光线遮蔽烟雾和燃烧气体中某些有毒气体种类的浓度。看见 5.12.5 了解更多信息。 1.8 燃烧行为通过照片或视频记录进行可视化记录。 1.9 单位- 在裁判决定中使用国际单位制；看见 IEEE/ASTM标准 硅-10 。括号中给出的单位仅供参考。 1.10 本标准用于测量和描述材料、产品或组件在受控条件下对热量和火焰的响应，但其本身并未包含实际火灾条件下材料、产品和组件的火灾危险或火灾风险评估所需的所有因素。 1.11 火灾测试本质上是危险的。 在进行这些试验时，应对人员和财产采取适当的保护措施。 1.12 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践，并确定监管限制的适用性。 1.13 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《国际标准、指南和建议制定原则决定》中确立的国际公认标准化原则制定的。 =====意义和用途====== 5.1 本试验方法提供了一种测量燃烧试样、床垫或带基础的床垫所产生的各种火灾试验响应特性的方法。 使用丙烷气体燃烧器点火后，允许试样在通风良好的条件下自由燃烧。在该测试方法中测量的最重要的火灾测试响应特性是热释放率，它量化了产生的火灾强度。 5.2 热释放速率通过耗氧原理来测量。 附件A3 讨论了假设和局限性。 5.3 该测试方法还提供了其他火灾测试响应特性的测量，包括烟雾遮蔽（作为烟雾释放速率、释放的总烟雾或烟雾的光学密度）、燃烧气体释放（作为燃烧气体浓度）和质量损失，这些对消防安全决策很重要。 5.4 在大多数火灾中，烟雾中最重要的气体成分是所有火灾中存在的碳氧化物。它们是大气毒性和燃烧完整性的指标。 碳氧化物浓度的测量有两个用途:( 1. )作为火灾危险评估计算的一部分，以及( 2. )以提高热释放测量的准确性。特定于某些材料的其他有毒燃烧气体也是大气毒性的指标，但对确定燃烧完整性不太重要，是可选措施；然而，火灾危险评估通常需要测量。 5.5 选择的点火类型（燃烧源）在公共场所的意外和故意火灾中都很常见。因此，该测试方法适用于公共场所的床垫。这些设施包括但不限于保健设施、老年疗养院、寄宿和护理院以及大学宿舍和宿舍。 5.6 本试验方法中使用以下三种配置之一: 5.6.1 测试配置A- 具有以下尺寸的试验室:3.66 m x 2.44 m x 2.44m（12 ft x 8 ft x 8英尺）高。 5.6.2 测试配置B- 具有以下尺寸的试验室:3.66 m x 3.05 m x 2.44 m（12 ft x 10 ft x 8 ft）高。 5.6.3 测试配置C- 开放式热量计（或家具热量计）。 5.7 其他尺寸的房间也可以接受，如果已经证明获得了等效的测试结果。 5.8 中列出的三种测试配置中的测量值 5.6 已经表明，在600 kW的热释放率下，管道中的热释放和质量损失也得到了类似的结果 ( 1. ) . 9 5.9 室内温度、气体浓度和烟雾遮蔽度的测量取决于房间大小。 5.10 本测试方法旨在为构建和操作能够按照CA TB 129要求运行测试的设备提供详细信息。 然而，该测试方法比技术公告更通用。 5.11 对床垫易燃性能的研究表明，台架火灾试验对于替代用途的组件材料的初步评估是有用的（参见 附录X3 ). 5.12 限制: 5.12.1 本试验方法不适用于香烟或任何其他阴燃源点燃。 5.12.2 本试验方法中的点火源为燃烧源，且已证明床垫，尤其是公共场所的床垫，与燃烧点火源有关。此外，这种特定的点火源已被证明能够在不同种类的床垫物品之间提供区分。然而，实际燃烧的床垫火灾发生的程度与此处使用的点燃程度相比或多或少是未知的。 5.12.3 当床垫在不同于规定的条件下燃烧时，尚不知道该测试方法的结果是否同样有效。 特别是，不清楚使用不同的点火源，或使用相同的点火源但具有不同的火焰暴露持续时间或不同的气体流速是否会改变结果。 5.12.4 与蔓延的床垫火灾和非蔓延的火灾之间的临界极限相对应的热释放速率的值是未知的。 5.12.5 到目前为止，排气管中的烟雾遮蔽或烟雾毒性测量值与整体火灾危险之间还没有已知的直接关系。 5.12.6 本测试方法不涉及因故意破坏或其他误用而可能发生的防火性能变化。

1.1 This is a fire-test-response standard. 1.2 This test method provides a means of determining the burning behavior of mattresses used in public occupancies by measuring specific fire test responses when the test specimen, a mattress or mattress with foundation, is subjected to a specified flaming ignition source under well ventilated conditions. 1.3 This is a test method for mattresses or mattresses with foundations. 1.4 Test data are obtained describing the burning behavior, following application of a specific ignition source, from ignition until all burning has ceased, a period of 1 h has elapsed, or flashover appears inevitable. 1.5 This test method does not provide information on the fire performance of mattresses under fire conditions other than those specified in this test method. In particular, this test method does not apply to smoldering ignition by cigarettes. See 5.12 for further information. 1.6 The rate of heat release of burning test specimen is measured by an oxygen consumption method. See 5.12.4 for further information. 1.7 Other measurements are the production of light-obscuring smoke and the concentrations of certain toxic gas species in the combustion gases. See 5.12.5 for further information. 1.8 The burning behavior is documented visually by photographic or video recordings. 1.9 Units— Use the SI system of units in referee decisions; see IEEE/ASTM SI-10 . The units given in parentheses are for information only. 1.10 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions. 1.11 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.12 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.13 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This test method provides a means of measuring a variety of fire-test-response characteristics resulting from burning a test specimen, mattress or mattress with foundation. After ignition using a propane gas burner, the test specimen is permitted to burn freely under well-ventilated conditions. The most important fire-test-response characteristic measured in this test method is the rate of heat release, which quantifies the intensity of the fire generated. 5.2 The rate of heat release is measured by the principle of oxygen consumption. Annex A3 discusses the assumptions and limitations. 5.3 This test method also provides measures of other fire-test-response characteristics, including smoke obscuration (as the rate of smoke release, total smoke released, or optical density of smoke), combustion gas release (as concentrations of combustion gases), and mass loss, which are important to making decisions on fire safety. 5.4 In the majority of fires, the most important gaseous components of smoke are the carbon oxides, present in all fires. They are indicators of the toxicity of the atmosphere and of the completeness of combustion. Measurement of concentrations of carbon oxides are useful for two purposes: ( 1 ) as part of fire hazard assessment calculations and ( 2 ) to improve the accuracy of heat release measurements. Other toxic combustion gases, which are specific to certain materials, are also indicators of the toxicity of the atmosphere, but are less crucial for determining combustion completeness and are optional measures; however, fire hazard assessment often requires their measurement. 5.5 The type of ignition chosen (flaming source) is common in both accidental and intentional fires in public occupancies. The test method is thus applicable to mattresses in public occupancies. Such facilities include, but are not limited to, health-care facilities, old age convalescent and board and care homes, and college dormitories and residence halls. 5.6 One of the following three configurations is to be used in this test method: 5.6.1 Test Configuration A— A test room with the following dimensions: 3.66 m by 2.44 m by 2.44 m (12 ft by 8 ft by 8 ft) high. 5.6.2 Test Configuration B— A test room with the following dimensions: 3.66 m by 3.05 m by 2.44 m (12 ft by 10 ft by 8 ft) high. 5.6.3 Test Configuration C— An open calorimeter (or furniture calorimeter). 5.7 Rooms of other dimensions are acceptable where it has been shown that equivalent test results are obtained. 5.8 Measurements in the three test configurations listed in 5.6 have been shown to give similar results for heat release in the duct, and mass loss, up to a rate of heat release of 600 kW ( 1 ) . 9 5.9 Measurements of temperatures, gas concentrations, and smoke obscuration in the room are dependent on room size. 5.10 This test method has been designed to provide details for the means to build and operate equipment capable of running tests as required by CA TB 129. However, this test method is more general than that technical bulletin. 5.11 Studies on the flammability performance of mattresses indicate that bench scale fire tests are useful for preliminary evaluations of component materials for substitution purposes (see Appendix X3 ). 5.12 Limitations: 5.12.1 This test method is not applicable to ignition by cigarettes, or by any other smoldering source. 5.12.2 The ignition source in this test method is a flaming source, and it has been shown that mattresses, particularly in public occupancies, are involved in fires with flaming ignition sources. Moreover, this particular ignition source has been shown to be able to provide a distinction between different kinds of mattress items. However, the fraction of actual flaming mattress fires occurring with ignitions more or less intense than that used here is not known. 5.12.3 It is not known whether the results of this test method will be equally valid when a mattress is burned under conditions different from those specified. In particular, it is unclear whether the use of a different ignition source, or the same ignition source but having a different duration of flame exposure or a different gas-flow rate, will change the results. 5.12.4 The value of rate of heat release corresponding to the critical limit between propagating mattress fires and non-propagating fires is not known. 5.12.5 As yet, there is not a known direct correlation between smoke obscuration or smoke toxicity measurements in the exhaust duct and overall fire hazard. 5.12.6 This test method does not address changes in fire performance that might occur due to vandalism or to other misuse.