首页 馆藏资源 舆情信息 标准服务 科研活动 关于我们
现行 ASTM D6256/D6256M-16
到馆提醒
收藏跟踪
购买正版
Standard Specification for Wood-Cleated Shipping Boxes with Skidded, Load-Bearing Bases 具有带挡板承重基座的木材装卸箱的标准规范
发布日期: 2016-12-01
1.1 本规范涵盖了带滑动承重底座的新型木钉箱的制造。本规范涵盖的箱子设计用于不受限制的国内和海外运输,装载量小于2500 lb[1134 kg],长度不大于16 ft[4877 mm](见 9.1 ). 受监管商品装运可能需要比本文规定更好的箱子(见 9.2 ). 1.2 带有滑动承重底座的木钉箱的性能取决于其制造部件;因此,规定了反映不同性能的各种类型、样式和类别。然而,本规范不包括在所有大气、搬运、运输和储存条件下的箱子性能。 1.3 如果可接受并允许使用其他施工方法或技术(参见 5.1.18 ),由此产生的包装系统应具有与使用这些指定材料和程序产生的性能相同或更好的性能。实践中规定的适当分配周期 D4169 可用于制定比较程序和标准。 1.4 以英寸-磅单位或国际单位表示的数值应单独视为标准值。在文本中,国际单位显示在括号中。每个系统中规定的值不是精确的等价物;因此,每个系统必须相互独立使用。将两个系统的值合并可能会导致不符合标准。 看见 IEEE/ASTM SI 10 用于单位转换。 1.5 本标准并非旨在解决与其使用相关的所有安全问题(如有)。标准使用者有责任在使用前制定适当的安全和健康实践,并确定监管限制的适用性。
1.1 This specification covers the fabrication of new wood-cleated boxes with skidded, load-bearing bases. Boxes covered by this specification are designed for nonregulated domestic and overseas shipment of loads less than 2500 lb [1134 kg] and not greater than 16 ft [4877 mm] in length (see 9.1 ). Regulated commodities shipments may require better boxes than those specified herein (see 9.2 ). 1.2 The performance of wood-cleated boxes with skidded, load-bearing bases is dependent on their fabricated components; therefore, a variety of types, styles, and classes reflecting varied performance are specified. This specification, however, does not cover box performance under all atmosphere, handling, shipping and storage conditions. 1.3 If the use of other construction methods or techniques are acceptable and permitted (see 5.1.18 ), the resulting packaging systems shall be of equal or better performance than would result from the use of these specified materials and procedures. The appropriate distribution cycle specified in Practice D4169 can be used to develop comparative procedures and criteria. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. See IEEE/ASTM SI 10 for conversion of units. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of the standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
分类信息
关联关系
研制信息
归口单位: D10.12
相似标准/计划/法规