BS EN 61377:2016适用于牵引系统，包括（适用时） 牵引电机、变流器、牵引控制设备，包括软件、变压器、， 输入滤波器、制动电阻器、主断路器、冷却设备、传感器、接触器、， 等等。图1只是一个概述，并不代表所有牵引系统架构。 集电器、机械制动系统和齿轮箱不在本标准范围内 标准本标准中适用的电机类型为异步电机或同步电机，包括 永磁体（PMM）或直流电（DC）。当辅助变流器封闭时，辅助变流器是范围的一部分 在牵引变流器内。否则，当牵引系统向辅助系统供电时 在牵引变流器外部，辅助系统可由等效负载替代。注1:本标准不考虑储能系统，因为储能系统没有具体的型式试验标准。 注2:辅助负载验证不属于本标准的一部分。注3:齿轮箱可以作为测试设置的一部分，但不是牵引系统的一部分。交叉引用:IEC 60050IEC 60349-1IEC 60349-2IEC TS 60349-3IEC 60349-4IEC 60850IEC 61133 IEC 61287-1IEC 62313EN 60349-1EN 60349-2EN 60349-4EN 61287-1IEC 60050-411IEC 60050-551IEC 60050-811IEC 60077-3IEC 60077-4IEC 60310IEC 60322IEC 6057IEC 62236-3-2IEC 62498-1ISO 14253-2ISO/IEC指南98-3:2008ISO/IEC指南99EN-IEC 60077-ISO-EN 60322EN-ISO-IEC 600425317025购买本文件时可获得的所有现行修订均包含在购买本文件中。

BS EN 61377:2016 applies to the traction system consisting (when it applies) of traction motor(s), converter(s), traction control equipment including software, transformer, input filters, brake resistors, main circuit-breaker, cooling equipment, transducers, contactors, etc.Figure 1 is just an overview and is not representative of all traction system architectures. Current collector, mechanical braking systems and gearbox are not in the scope of this standard.Types of motors applicable in this standard are asynchronous, or synchronous including permanent magnet (PMM), or direct current (DC).The auxiliary converter(s) is (are) part of the scope when the auxiliary converter is enclosed within the traction converter. Otherwise, when the traction system feeds an auxiliary system outside the traction converter, the auxiliary system can be replaced by an equivalent load.NOTE 1 Energy storage system is not considered in this standard since there is no specific type test standard for energy storage system.NOTE 2 Auxiliary loads validation is not part of this standard.NOTE 3 The gearbox can be part of test set-up, but it is not a part of traction system.Cross References:IEC 60050IEC 60349-1IEC 60349-2IEC TS 60349-3IEC 60349-4IEC 60850IEC 61133IEC 61287-1IEC 62313EN 60349-1EN 60349-2EN 60349-4EN 61287-1IEC 60050-411IEC 60050-551IEC 60050-811IEC 60077-3IEC 60077-4IEC 60310IEC 60322IEC 60571IEC 62236-3-1IEC 62236-3-2IEC 62498-1ISO 14253-2ISO 17025ISO/IEC Guide 98-3:2008ISO/IEC Guide 99EN 60077-3EN 60077-4EN 60310EN 60322EN ISO 14253-2EN ISO/IEC 17025All current amendments available at time of purchase are included with the purchase of this document.