1.1 本试验方法利用赛波特糠醇粘度计测量乳化沥青的稠度。适用于规范中规定的所有乳化沥青 D977 和 D2397/D2397M . 1.2 以国际单位制或英寸-磅单位表示的数值应单独视为标准值。每个系统中规定的值可能不是精确的等效值；因此，每个系统应相互独立使用。将两个系统的值合并可能会导致不符合标准。 1.3 本标准的文本引用了提供解释材料的注释和脚注。这些注释和脚注（不包括表和图中的注释和脚注）不应视为本标准的要求。 1.4 本标准并非旨在解决与其使用相关的所有安全问题（如有）。 本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 3.1 粘度在乳化沥青的使用中具有重要意义，因为它是一种影响其效用的特性。在施工应用类型中使用时，材料必须足够薄，以便均匀地通过喷洒器的喷管喷洒，但必须足够厚，使其不会从路拱或路面流出。 对于混合级乳液，粘度可能会影响骨料的可混合性和由此产生的膜厚。许多乳化沥青的粘度受剪切力的影响。因此，严格遵守测试程序是实现精度的必要条件。

1.1 This test method utilizes the Saybolt Furol viscometer to measure the consistency of emulsified asphalt. It is applicable to all the emulsified asphalts specified in Specifications D977 and D2397/D2397M . 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in noncompliance with the standard. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 3.1 Viscosity has significance in the use of emulsified asphalts because it is a property which affects their utility. When used in application types of construction, the material must be thin enough to be uniformly applied through the spray bar of distributor, yet thick enough so that it will not flow from the crown or grade of the road. For mixing-grade emulsions, the viscosity may affect mixability and resulting thickness of film on the aggregate. The viscosity of many emulsified asphalts is affected by shear. Therefore, strict adherence to test procedure is necessary to achieve precision.