AS/NZS 4387.4:1996[ Pending Revision ]-家用厨房组件.试验方法方法4:工作台面和底面强度的测定-国家数字标准馆

现行 AS/NZS 4387.4:1996[ Pending Revision ]

到馆提醒

收藏跟踪

购买正版

Domestic kitchen assemblies - Methods of test, Method 4: Determination of the strength of worktops and bottom surfaces 家用厨房组件.试验方法方法4:工作台面和底面强度的测定

发布日期： 1996-06-05

本标准规定了确定厨房单元台面和底面的强度的程序。

This Standard sets out the procedure for determining the strength of worktops and bottom surfaces of kitchen units.

分类信息

发布单位或类别：澳大利亚-澳大利亚/新西兰标准

关联关系

研制信息

相似标准/计划/法规

AS/NZS 4387.2-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 2: Determination of shelf deflection
家用厨房组件.试验方法方法2:搁板挠度的测定

AS/NZS 4387.14-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 14: Determination of strength of handles
家用厨房组件.试验方法方法14:把手强度的测定

AS/NZS 4387.11-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 11: Determination of slam shut of drawers
家用厨房组件.试验方法方法11:抽屉关闭度的测定

AS/NZS 4387.5-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 5: Determination of strength of hinged doors
家用厨房组件.试验方法方法5:铰链门强度的测定

AS/NZS 4387.10-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 10: Determination of slam open of drawers
家用厨房组件.试验方法方法10:抽屉猛然打开的测定

AS/NZS 4387.1-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 1: Determination of strength of carcass and underframe
家用厨房组件.试验方法方法1:屠体和底架强度的测定

AS/NZS 4387.3-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 3: Determination of strength of shelf supports
家用厨房组件.试验方法方法3:架子支架强度的测定

AS/NZS 4387.7-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 7: Determination of slam shut of hinged doors
家用厨房组件.试验方法方法7:铰链门关闭的测定

AS/NZS 4387.16-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 16: Determination of calibration of drawer slamming apparatus
家用厨房组件.试验方法方法16:抽屉砰击装置校准的测定

AS/NZS 4387.8-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 8: Determination of wear and fatigue of hinged doors
家用厨房组件.试验方法方法8:铰链门磨损和疲劳的测定

AS/NZS 4387.6-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 6: Determination of slam open of hinged doors
家用厨房组件.试验方法方法6:铰链门砰然打开的测定

AS/NZS 4387.12-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 12: Determination of retention of the bottom surface of drawers
家用厨房组件.试验方法方法12:抽屉底面保持力的测定

AS/NZS 4387.13-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 13: Determination of wear and fatigue of drawers, sliding shelves and runners
家用厨房组件.试验方法方法13:抽屉滑动架和滑槽磨损和疲劳的测定

AS/NZS 4387.15-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 15: Determination of the strength of support frames for wall attachment devices
家用厨房组件.试验方法方法15:墙壁连接装置支撑框架强度的测定

AS/NZS 4387.0-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Part 0: Introduction, list of methods and general requirements
家用厨房组件.试验方法第0部分:介绍方法列表和一般要求

AS/NZS 4387.9-1996[ Pending Revision ]

Domestic kitchen assemblies - Methods of test, Method 9: Determination of resistance to downward static load on drawers and other runner-supported items
家用厨房组件.试验方法方法9:抽屉和其他由转轮支撑的物品抗向下静载荷的测定

ISO 16525-4-2014

Adhesives — Test methods for isotropic electrically conductive adhesives — Part 4: Determination of shear strength and electrical resistance using rigid-to-rigid bonded assemblies
粘合剂——各向同性导电粘合剂试验方法第4部分:用刚性对刚性粘合组件测定剪切强度和电阻

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 4: Determination of open assembly time under referenced conditions
酚醛和氨基塑料以外的承重木结构用胶粘剂.试验方法.第4部分:参考条件下开放装配时间的测定

UNE-EN 15416-4-2007

Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 4: Determination of open assembly time for one component polyurethane adhesives
酚醛和氨基塑料以外的承重木结构用胶粘剂.试验方法.第4部分:单组分聚氨酯胶粘剂的开放装配时间的测定

《国家标准化发展纲要》提出建设国家数字标准馆，推动标准化工作向数字化、网络化、智能化转型。中国标准化研究院正在全力推进国家数字标准馆建设，力争在2026年底建成“一个中心”和“一个平台”，即全球领先的标准数据资源中心，涵盖标准全生命周期的数字化、网络化、智能化研究与服务平台。

专题数据库

标准管理系统

大数据分析系统

标准智能研制系统