CISPR 15:20 18适用于射频干扰的发射（辐射和传导）: -照明设备(3.3.16)； -多功能设备的照明部分，其中该照明部分是主要功能； -用于住宅和非工业应用的紫外线和红外线辐射设备； -广告标志； -装饰照明； -紧急标志。 不包括在本文档范围内的有:？ -拟内置于照明设备中且用户不可更换的组件或模块； -在ISM频段工作的照明设备（如国际电联无线电条例第63（1979）号决议所界定）； -飞机和机场设施（跑道、服务设施、平台）的照明设备； -视频标志； -设施； -无线电中电磁兼容性要求的设备-在其他CISPR标准中明确规定了频率范围，即使它们包含内置照明功能。 覆盖的频率范围为9 kHz至400 GHz。无需在本文件中未规定限值的频率下进行测量。 同时受本文件和/或其他标准不同条款约束的多功能设备需要在相关功能运行的情况下满足各条款/标准的规定。 对于本文件范围之外且包括照明作为次要功能的设备，无需根据本文件单独评估照明功能，前提是照明功能在评估期间根据适用标准有效。本文件中的辐射发射要求不适用于ITU定义的无线电发射机的有意发射，也不适用于与这些相关的任何杂散发射e故意传播。 在本文件的其余部分中，无论何时使用术语“照明设备”或“EUT”，其意指属于本条款中规定的本文件范围内的电气照明和类似设备。本第九版取消并取代2013年出版的第八版及其修正案1:20 15。本版构成技术修订版。与上一版相比，此版本包括以下重大技术变更: a)全面的编辑修订和重组； b)范围内删除了对市电和电池操作的限制； c)引入了300 MHz至1 GHz频率范围内的辐射干扰限值； d)负载终端限制和CDNE（辐射排放的替代）限制已发生变化；e)删除插入损失要求和相关附件A； f)介绍三个基本端口:有线网络端口、本地有线端口和机箱端口； g)采用更加独立于技术的方法； h)用适当参考CISPR 16系列标准取代附件B(CDNE)； i)对锥形壳体的金属孔的修改要求； j)GU10自镇流灯传导干扰测量新方法； k)增加电流探头测量方法和各种类型端口的限值（除电压限值和测量方法外）； l)引入术语“模块”（而不是独立辅助）以及使用主机（参考）系统测量模块的要求； m)EUT稳定时间的修改质量标准；n）对于大型EUT（>1.6 m），增加了在3 m距离使用60 cm环形天线的磁场测量方法（CISPR 14-1的方法），作为3 m和4 m LAS的替代方法。 关键词:射频干扰的发射（辐射和传导）

CISPR 15:2018 applies to the emission (radiated and conducted) of radiofrequency disturbances from:
- lighting equipment (3.3.16);
- the lighting part of multi-function equipment where this lighting part is a primary function;
- UV and IR radiation equipment for residential and non-industrial applications;
- advertising signs;
- decorative lighting;
- emergency signs.
Excluded from the scope of this document are:？
- components or modules intended to be built into lighting equipment and which are not user-replaceable;
- lighting equipment operating in the ISM frequency bands (as defined in Resolution 63 (1979) of the ITU Radio Regulation);
- lighting equipment for aircraft and airfield facilities (runways, service facilities, platforms);
- video signs;
- installations;
- equipment for which the electromagnetic compatibility requirements in the radio-frequency range are explicitly formulated in other CISPR standards, even if they incorporate a built-in lighting function.
The frequency range covered is 9 kHz to 400 GHz. No measurements need to be performed at frequencies where no limits are specified in this document.
Multi-function equipment which is subjected simultaneously to different clauses of this document and/or other standards need to meet the provisions of each clause/standard with the relevant functions in operation.
For equipment outside the scope of this document and which includes lighting as a secondary function, there is no need to separately assess the lighting function against this document, provided that the lighting function was operative during the assessment in accordance with the applicable standard. The radiated emission requirements in this document are not intended to be applicable to the intentional transmissions from a radio transmitter as defined by the ITU, nor to any spurious emissions related to these intentional transmissions.
Within the remainder of this document, wherever the term "lighting equipment" or "EUT" is used, it is meant to be the electrical lighting and similar equipment falling in the scope of this document as specified in this clause. This ninth edition cancels and replaces the eighth edition published in 2013 and its Amendment 1:2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) full editorial revision and restructuring;
b) the restriction to mains and battery operation is deleted in the scope;
c) radiated disturbance limits in the frequency range 300 MHz to 1 GHz have been introduced;
d) the load terminals limits and the CDNE (alternative to radiated emissions) limits have changed;
e) deletion of the insertion-loss requirements and the associated Annex A;
f) introduction of three basic ports: wired network ports, local wired ports and the enclosure port;
g) introduction of a more technology-independent approach;
h) replacement of Annex B (CDNE) by appropriate references to CISPR 16-series of standards;
i) modified requirements for the metal holes of the conical housing;
j) new conducted disturbance measurement method for GU10 self-ballasted lamp;
k) addition of current probe measurement method and limits for various types of ports (in addition to voltage limits and measurement methods);
l) introduction of the term ‘module’ (instead of independent auxiliary) and requirements for measurement of modules using a host (reference) system;
m) modified specifications for stabilization times of EUTs;
n) for large EUT (> 1,6 m), addition of the magnetic field measurement method using a 60 cm loop antenna at 3 m distance (method from CISPR 14-1) as an alternative to the 3 m and 4 m LAS.
Keywords: emission (radiated and conducted) of radiofrequency disturbance