BS ISO 23551-10:2016规定了安全、设计、施工和性能要求，以及 燃气燃烧器用自动排气阀（以下简称“阀门”）的试验 燃烧一种或多种气体燃料的器具。ISO 23551的本部分适用于声明的最大进口压力达到和的阀门 包括标称连接尺寸小于等于DN 100（4“）的500 kPa（5 bar）。ISO 23551的本部分适用于正常开启的阀门、电动阀门和由流体驱动的阀门，这些阀门的控制阀 流体是电动驱动的，但不会连接到任何用于切换控制信号或控制信号的外部设备 驱动能量，以及装有开启位置指示开关的阀门。 ISO 23551的本部分不适用于使用可再生能源和/或废气（即具有腐蚀性的气体）的燃烧器和电器的阀门 特性），如果阀门与可再生能源和/或废气接触，建议使用本部分 仅当提供了明确的信息且相关的测试方法和要求 明确规定。用于露天安装并暴露于室外环境的设备的阀门，直接连接到主管道或保持标准的容器的阀门 分配压力，以及适用于油的阀门。ISO 23551的本部分仅适用于型式试验。注:未规定制造商进行最终产品检验和测试的规定。交叉引用:ISO 23550:2011ISO 6708ISO 8655-1ISO 23551ISO 23552-1ISO 23553-1IEC 61010IEC 61508ANSI/ASME B 1.1:1989ANSI/ASME B 1.20.1ANSI/ASME B 16.1ANSI/SAE J 514JIS B 0202JIS B 0203JIS B 2220JIS B 2239JIS B 2240JIS B 2241JIS B 2301JIS B 2316JIS B 2311JIS B 2316JIS 3401购买本产品时所有现有的修改件均包括在内文件

BS ISO 23551-10:2016 specifies the safety, design, construction and performance requirements and testing for automatic vent valves (hereafter referred to as "valves") for use with gas burners, gas appliances burning one or more gaseous fuels.This part of ISO 23551 is applicable to valves with declared maximum inlet pressures up to and including 500 kPa (5 bar) of nominal connection sizes up to and including DN 100 (4").This part of ISO 23551 is applicable tonormally open valves,electrically operated valves and to valves actuated by fluids where the control valves for these fluids are actuated electrically, but not to any external devices for switching the control signal or actuating energy, andvalves fitted with open position indicator switches. This part of ISO 23551 is not applicable tovalves for burners and appliances using renewables and/or waste gases (i.e. gases having corrosive characteristics),In case valves are in contact with renewables and/or waste gases, it is recommend to use this part of ISO 23551 only if explicit information is provided and relevant test methods and requirements are specified.valves for appliances intended to be installed in the open air and exposed to the outdoor environment,valves that are connected directly to mains pipe-work or to a container that maintains a standard distribution pressure, andvalves suitable with oil.This part of ISO 23551 is applicable to type testing only.NOTE Provisions for final product inspection and testing by the manufacturer are not specified.Cross References:ISO 23550:2011ISO 6708ISO 8655-1ISO 23551ISO 23552-1ISO 23553-1IEC 61010IEC 61508ANSI/ASME B 1.1:1989ANSI/ASME B 1.20.1ANSI/ASME B 16.1ANSI/SAE J 512ANSI/SAE J 514JIS B 0202JIS B 0203JIS B 2220JIS B 2239JIS B 2240JIS B 2241JIS B 2301JIS B 2302JIS B 2311JIS B 2312JIS B 2316JIS H 3401All current amendments available at time of purchase are included with the purchase of this document.