家用和类似用途的自动电气控制装置；第2部分:电动机起动继电器的特殊要求SUL 60730-2-101范围和规范性参考第1部分的本条款适用，但以下情况除外:1.1更换:IEC 60730的本部分适用于自动控制与家用和类似用途设备相关的单相电动机起动绕组的控制装置。本标准适用于使用NTC或PTC热敏电阻的电机起动继电器，其附加要求见附录J。 1.1DV在1.1中增加以下内容:本标准还包括拟集成到电机中的离心开关。此类设备将使用预期电机作为集成控制装置进行测试。 1.1.1本标准适用于固有安全、与设备安全相关的操作值、操作时间和操作顺序，以及家用或类似设备中或与之相关的电机启动继电器的测试。非正常家用设备的电动机起动继电器，但可能供公众使用，如商店、轻工业和农场的非专业人员使用的设备，均在本标准的范围内。本标准不适用于专为工业应用设计的电机起动继电器。在本标准中，“设备”一词是指“器具和设备”“启动继电器”的意思是“电机”- 启动继电器。“1.1.2本标准适用于包含电子设备的启动继电器，以及使用热敏电阻元件、热元件和磁性元件的启动继电器。1.1.3本标准不适用于通用继电器或IEC 60947系列所涵盖类型的接触器和电动机起动器。本标准不适用于机械计时器或机械操作电动机启动设备。1.1.3DV删除1.1.3第二句中的以下内容:“或机械操作的电动机起动装置”IEC 60947（所有部分）、低压开关设备和控制设备1。1.4本标准适用于与启动继电器电气和/或机械集成的手动控制装置。 IEC 61058-1.1.2更换中包含了不构成启动继电器一部分的手动开关的要求:本标准适用于额定电压不超过690 V、额定电流不超过63 a.1.2DV的启动继电器。在1.2中增加了以下内容:最大电压为600 V。最大电流不受限制。1.3更换:如果启动继电器的响应值取决于在设备中安装启动继电器的方法，则本标准不考虑启动继电器自动动作的响应值。如果响应值对保护用户或周围环境具有重要意义，则应适用适当家用设备标准中定义的值或制造商确定的值。 1.4更换:本标准也适用于包含电子装置的电机起动继电器，其要求见附录H。

Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Motor Starting RelaysUL 60730-2-101 Scope and normative referencesThis clause of Part 1 is applicable except as follows:1.1 Replacement:This part of IEC 60730 applies to controls for automatically controlling the starting windings of single phase motors associated with equipment for household and similar use.This standard applies to motor-starting relays using NTC or PTC thermistors, additional requirements for which are contained in Annex J. 1.1DV Addition of the following text to 1.1:This standard also covers centrifugal switches intended to be integrated into motors. Such devices are tested with the intended motor as an integrated control.1.1.1 This standard applies to the inherent safety, to the operating values, operating times and operating sequences where such are associated with equipment safety, and to the testing of motor starting relays used in, or in association with, household or similar equipment.Motor-starting relays for equipment not intended for normal household use, but which nevertheless may be used by the public, such as equipment intended to be used by laymen in shops, in light industry and on farms, are within the scope of this standard.This standard does not apply to motor-starting relays designed exclusively for industrial applications.Throughout this standard, the word "equipment" means "appliance and equipment." The words "starting relay" mean "motor-starting relay."1.1.2 This standard applies to starting relays incorporating electronic devices, and starting relays using thermistor elements, thermal elements and magnetic elements.1.1.3 This standard does not apply to general purpose relays or to contactors and motor starters of the type covered by the IEC 60947 series. This standard does not apply to mechanical timers or mechanically operated motor-starting devices.1.1.3DV Deletion of the following text from the second sentence of 1.1.3:"or mechanically operated motor-starting devices"IEC 60947 (all parts), Low-voltage switchgear and controlgear1.1.4 This standard applies to manual controls when such are electrically and/or mechanically integral with starting relays.Requirements for manual switches not forming part of a starting relay are contained in IEC 61058-1.1.2 Replacement:This standard applies to starting relays with a rated voltage not exceeding 690 V and with a rated current not exceeding 63 A.1.2DV Addition of the following text to 1.2:The maximum voltage is 600 V. The maximum current is unlimited.1.3 Replacement:This standard does not take into account the response value of an automatic action of a starting relay, if such a response value is dependent upon the method of mounting the starting relay in the equipment. Where a response value is of significant purpose for the protection of the user or surroundings, the value defined in the appropriate household equipment standard or as determined by the manufacturer shall apply.1.4 Replacement:This standard applies also to motor-starting relays incorporating electronic devices, requirements for which are contained in annex H.