BS EN 13121-3:2016给出了设计、制造、检验、测试和试验的要求 玻璃钢储罐和容器的验证，带或不带热塑性塑料衬里，用于储存或加工 液体，工厂制造或现场制造，非加压或加压至10巴，供地面上使用。 规范性附录G中给出了进一步的要求。EN 13121本部分中使用的术语“容器和储罐”包括分支至 通过螺栓和支架、支架或其他附件与管道工程或其他设备连接 直接粘在外壳上。EN 13121的这一部分包括温度在-40°C和120°C之间的容器和储罐。不包括在EN 13121的这一部分中的有:用于运输液体的储罐和容器；地下储罐；球形容器；形状不规则的容器和储罐；双壁结构的双安全壳储罐和容器；有爆炸危险的储罐和容器，或其故障可能导致事故的储罐和容器 放射性排放；储存用整体和分段结构的纤维增强水箱规范， 地上冷水（见EN 13280）。交叉引用:EN 59EN 1092-1EN 1990EN 1991？1）n n n n n n n n n n n n n n n n n n n n n n n（1）1）1 1 1）3 3 3 3 3）1 1）1）1 1）3 3）3）1 1）1 1）1）1）1 1 1 1 1 1）1 1 1 1）1 1 1 1 1 1 1 1 1 1 1 1 1）1 1 1 1 1）1 1 1 1 1）1 1）1 1 1）1 1 1）1 1 1 1）1 1 1 1 1）1）1 1）1）1 1 1）1 1）1 1 1 1 1 1）1 1）1）1）1）1 1 1）1）1 1 1）1）1）1）1）1 1）1）1）1）1）1）1）1）1）1 1 1 1 1 1 1 1）1 1 1 1 1）1 1）1）1）1 1 1 1 1）3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1-5EN 1991-1991-4EN 1991 9-2EN ISO 1172ISO 1172EN ISO 2592ISO 2592EN ISO 3915ISO 3915EN ISO 7500-1ISO 7500-1EN ISO 9513ISO 9513ENISO 11357-2ISO 11357-2EN ISO 14125ISO 14125EN ISO 14692-3:2002ISO 14692-3:2002ISO 48ASTM D4541-09ASME B16。5/16.47EN 1993-1-3:2006EN 1991-1-6CEN/TR 13121-5EN 13280IEC 60721-2-697/23/ECEN 15912014/68/EU购买本文件时可获得的所有现行修订均包含在购买本文件中。

BS EN 13121-3:2016 gives requirements for the design, fabrication, inspection, testing and verification of GRP tanks and vessels with or without thermoplastics lining for storage or processing of fluids, factory made or site built, non-pressurized or pressurized up to 10 bar, for use above ground. Further requirements are presented in normative Annex G.The terms vessels and tanks as used in this part of EN 13121 include branches up to the point of connection to pipe work or other equipment by bolting and supports, brackets or other attachments bonded directly to the shell.This part of EN 13121 covers vessels and tanks subject to temperatures between -40 °C and 120 °C.Excluded from this part of EN 13121 are:tanks and vessels for the transport of fluids;underground storage tanks;spherical vessels;vessels and tanks of irregular shape;tanks and vessels with double containment where the double wall is considered structural;tanks and vessels which are subject to the risk of explosion, or failure of which may cause an emission of radioactivity;specification for fibre reinforced cisterns of one piece and sectional construction for the storage, above ground, of cold water (see EN 13280).Cross References:EN 59EN 1092-1EN 1990EN 1991?1-1EN 1991-1-3EN 1991-1-4EN 1991-1-5EN 1991-4EN 1993EN 1993-1-1EN 1993-1-6:2007EN 1998EN 1998-1EN 1998-4:2006EN 10025-2EN 13067EN 13121-1:2003EN 13121-2:2003EN 13121-4EN 13445-3:2014EN 13555EN 13923EN ISO 75-2ISO 75-2EN ISO 291ISO 291EN ISO 527-4ISO 527-4EN ISO 899-1ISO 899-1EN ISO 899-2ISO 899-2EN ISO 1172ISO 1172EN ISO 2592ISO 2592EN ISO 3915ISO 3915EN ISO 7500-1ISO 7500-1EN ISO 9513ISO 9513EN ISO 11357-2ISO 11357-2EN ISO 14125ISO 14125EN ISO 14692-3:2002ISO 14692-3:2002ISO 48ASTM D4541-09ASME B16.5/16.47EN 1993-1-3:2006EN 1991-1-6CEN/TR 13121-5EN 13280IEC 60721-2-697/23/ECEN 15912014/68/EUAll current amendments available at time of purchase are included with the purchase of this document.