1.1 本规范涵盖由任何纺织纤维或纤维混合物组成的机织和经编被子织物。 1.2 这些要求适用于与织物方向相关的那些属性的长度和宽度方向。 1.3 以下安全危害警告仅适用于本说明书中描述的试验方法: 本标准并不旨在解决与其使用相关的所有安全性问题（如果有）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践并确定法规限制的适用性。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。======意义和用途====== 5.1 经买卖双方同意，用于该最终用途的织物应符合 表1 本规范的。 5.2 人们认识到，出于时尚或美学的目的，由这些织物制成的制品的最终消费者可能会发现不符合以下所有要求的可接受织物: 表1 因此， 表1 可由买卖双方协商修改。 5.2.1 如果中的任何要求 表1 经买卖双方同意修改后，任何对规范的引用应声明:“该织物符合ASTM规范 D4769 ，以下特征除外。” 5.3 凡买卖双方未达成预购协议，且如有争议， 表1 仅用作指南。如 5.2 最终消费者需求决定了任何特定类型织物的不同性能参数。 5.4 特定性质和测试方法的重要性和用途在指定测试方法的适当章节中讨论。

1.1 This specification covers woven and warp knitted comforter fabrics, composed of any textile fiber, or mixture of fibers. 1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.3 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 Upon mutual agreement between the purchaser and seller, fabrics intended for this end use should meet all the requirements listed in Table 1 of this specification. 5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1 . Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and seller. 5.2.1 If any of the requirements in Table 1 are modified by mutual agreement between purchaser and seller, any reference to the specification shall state that: “This fabric meets ASTM Specification D4769 , except for the following characteristic(s).” 5.3 Where no prepurchase agreement has been reached between the purchaser and seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As stated in 5.2 , ultimate consumer demands dictate varying performance parameters for any particular style of fabric. 5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.