BS EN 50124-1:2017涉及铁路绝缘协调。适用于使用的设备 在信号、机车车辆和固定装置中。绝缘协调涉及绝缘的选择、尺寸和相关性 设备项目内部和项目之间。在绝缘尺寸、电应力和 考虑了环境条件。对于相同的条件和应力，这些 尺寸是一样的。绝缘协调的目标是避免不必要的绝缘尺寸过大。 本标准规定:设备的电气间隙和爬电距离要求；与绝缘配合有关的试验的一般要求。“设备”一词与第3.3节中定义的部分有关，它可能适用于系统、子系统和 仪器，设备的一部分，或等电位线的物理实现。本标准不涉及:通过固体或液体绝缘的距离；通过气体而非空气的距离；非大气压下通过空气的距离；在极端条件下使用的设备。 产品标准应与本通用标准保持一致。然而，由于安全性和/或可靠性的原因，他们可能需要有理由的不同要求 原因，例如信号，和/或设备本身的特殊操作条件，例如:。 架空接触线应符合EN 50119。本标准还规定了设备的介电试验（型式试验或常规试验）（见 附件B）。注:对于安全关键系统，需要特定要求。这些要求见 特定于产品的信号标准EN 50129。 交叉引用:EN 50123EN 50163EN 60060-1IEC 60060-1EN 60071-1IEC 60071-1EN 60112IEC 60112EN 60587IEC 60587EN 60664-1:2007IEC 60664-1:20072008/57/ECEN 50121EN 50125EN 50129EN 50152EN 50153EN 60071-2IEC 60071-2EN 60077-1EN 60099-1EN 60099-4IEC 60099-4EN 60168IEC 60364IEC 60364EN 60383-1EN 60383-2EC 60383-2EN 60507IEC 6052IEC60660EN 60664-3CEC 60664-3EN 60664-5IEC 60664-5EN 60947-1IEC 60947-1EN 61109IEC 61245EN 61558IEC 61558EN 61936-1IEC 61936-1EN 62271-1IEC 1IEC/TR 60099-3IEC 60664-2-1IEC/TR 60815:1986IEC/TS 60815EN 50119购买本文件时可获得的所有现行修订均包含在购买本文件中。

BS EN 50124-1:2017 deals with insulation coordination in railways. It applies to equipment for use in signalling, rolling stock and fixed installations.Insulation coordination is concerned with the selection, dimensioning and correlation of insulation both within and between items of equipment. In dimensioning insulation, electrical stresses and environmental conditions are taken into account. For the same conditions and stresses, these dimensions are the same.An objective of insulation coordination is to avoid unnecessary over dimensioning of insulation.This standard specifies:requirements for clearances and creepage distances for equipment;general requirements for tests pertaining to insulation coordination.The term equipment relates to a section as defined in 3.3 it may apply to a system, a sub-system, an apparatus, a part of an apparatus, or a physical realization of an equipotential line.This standard does not deal with:distances through solid or liquid insulation;distances through gases other than air;distances through air not at atmospheric pressure;equipment used under extreme conditions.Product standards should align with this generic standard.However, they may require, with justification, different requirements due to safety and/or reliability reasons, e.g. for signalling, and/or particular operating conditions of the equipment itself, e.g. overhead contact lines which should comply with EN 50119.This standard also gives provisions for dielectric tests (type tests or routine tests) on equipment (see Annex B).NOTE For safety critical systems, specific requirements are needed. These requirements are given in the product specific signalling standard EN 50129.Cross References:EN 50123EN 50163EN 60060-1IEC 60060-1EN 60071-1IEC 60071-1EN 60112IEC 60112EN 60587IEC 60587EN 60664-1:2007IEC 60664-1:20072008/57/ECEN 50121EN 50125EN 50129EN 50152EN 50153EN 60071-2IEC 60071-2EN 60077-1IEC 60077-1EN 60099-1IEC 60099-1EN 60099-4IEC 60099-4EN 60168IEC 60168EN 60364IEC 60364EN 60383-1IEC 60383-1EN 60383-2IEC 60383-2EN 60507IEC 60507EN 60529IEC 60529EN 60660IEC 60660EN 60664-3IEC 60664-3EN 60664-5IEC 60664-5EN 60947-1IEC 60947-1EN 61109IEC 61109IEC 61245EN 61558IEC 61558EN 61936-1IEC 61936-1EN 62271-1IEC 62271-1IEC/TR 60099-3IEC 60664-2-1IEC/TR 60815:1986IEC/TS 60815EN 50119All current amendments available at time of purchase are included with the purchase of this document.