BS PD IEC/TS 63066:2017适用于对接连接器（以下简称附件） 并入或固定在电气设备上，用于连接可移动能源 存储单元到专用电力转换单元、能耗单元或 另一个储能装置。这些附件适用于直流，可能包括接地触点和/或选装件 用于信号和数据的辅助触点。这些附件的额定电流高达 800 A，额定工作电压不超过1000 V DC。这些附件不适合在负载下配对或拆卸。这些配件是 拟由受指导人员（IEC 60050-195-1998，195-04-02）或技术人员安装 仅限人员（IEC 60050-195-1998，195-04-01）。首选评级列表并不打算排除其他评级。 本文件适用于在中所述环境条件下使用的附件 第32条。这些附件旨在连接到铜或铜的载流部件 仅合金，电镀或未电镀。本文件也适用于在超低电压下使用的附件。在特殊条件盛行的位置，例如车载车辆，额外 要求可能适用。这些附件用于特定的充电系统。注:对于运行以外的条件，可适用其他要求，例如IEC 62133和联合国关于危险货物运输的建议第38.338.3节。交叉引用:IEC 60309-1:1999IEC 60309-1:1999/AMD1:2005IEC 60309-1:1999/AMD2:2012IEC 60068-2- 2-6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 IEC 60884-1:2002/AMD2:2013IEC 62133ISO 61750-3:2012发布时的所有现行修订版购买本文件时包括购买费用。

BS PD IEC/TS 63066:2017 applies to docking connectors (hereinafter referred to as accessories) incorporated in or fixed to electrical equipment, intended to connect removable energy storage units to a dedicated electric power conversion unit, to an energy consuming unit or to another energy storage unit.These accessories are intended for DC and may include an earth1 contact and/or optional auxiliary contacts for signaling and data. These accessories have a rated current of up to 800 A and rated operating voltages not exceeding 1 000 V DC.These accessories are not suitable for mating or unmating under load. These accessories are intended to be installed by instructed persons (IEC 60050-195:1998, 195-04-02) or skilled persons (IEC 60050-195:1998, 195-04-01) only.The list of preferred ratings is not intended to exclude other ratings.This document applies to accessories for use under environmental conditions as described in Clause 32.These accessories are intended to be connected to current carrying parts in copper or copper alloy only, plated or not plated.This document also applies to accessories intended to be used at extra-low voltage.In locations where special conditions prevail, for example on board vehicles, additional requirements may apply.These accessories are intended to be used with a specific charging system.NOTE For conditions other than operation, additional requirements could be applicable, for instance IEC 62133 and the UN Recommendations on the Transport of Dangerous Goods section 38.338.3.Cross References:IEC 60309-1:1999IEC 60309-1:1999/AMD1:2005IEC 60309-1:1999/AMD2:2012IEC 60068-2-1IEC 60068-2-2IEC 60068-2-14IEC 60068-2-30IEC 60068-2-38IEC 60068-2-52IEC 60068-2-60IEC 60309-1:1999IEC 60309-1:1999/AMD1:2005IEC 60309-1:1999/AMD2:2012IEC 60352IEC 60417IEC 61140:2016IEC 61373:2010ISO/IEC TR 29106:2007ISO/IEC TR 29106:2007/AMD1:2012IEC 60050-195IEC 60884-1:2002IEC 60884-1:2002/AMD1:2006IEC 60884-1:2002/AMD2:2013IEC 62133ISO 61750-3:2012All current amendments available at time of purchase are included with the purchase of this document.