1.1 本规范定义了用于维修耐用、刚性、可重新定位结构的夹层板的粘合剂所需的特性。 1.1.1 本规范涵盖了两部分环氧粘合剂，适用于将铝合金饰面粘接到非金属芯、芯到芯、芯到周边铝挤压框架，以修复耐用的刚性壁可移动结构。粘合剂应适用于形成能够承受以下温度的粘合剂: −54 °C至93 °C(−65 华氏度至199度 °F）和高相对湿度，也能承受预期在使用中遇到的应力、温度和相对湿度的组合。 粘合剂也应适用于面板嵌入件和边缘附件的粘接。 1.2 如果只给出国际单位制，或者先给出国际单位制，然后再给出英寸-磅单位，则以国际单位制表示的值应视为标准值；如果先给出英寸-磅单位，然后是国际单位制，则英寸-磅单位应视为标准。 1.3 以下安全隐患警告仅适用于本规范中描述的测试方法。 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 6.1 用于维修耐用、刚性、可重新定位结构的夹芯板的粘合剂必须具有机械性能水平和环境阻力的组合，以确保粘合剂在暴露于恶劣气候条件下时的长期耐久性。此外，这些粘合剂必须具有可加工性特征，允许在各种维修场景和环境中使用。 6.2 本规范定义了用于维修耐用、刚性、可重新定位结构的夹层板的粘合剂所需的特性。

1.1 This specification defines those characteristics that are required of adhesives to be used in the repair of sandwich panels for durable, rigidwall, relocatable structures. 1.1.1 This specification covers two-part epoxy adhesive suitable for bonding aluminum alloy facings to nonmetallic core, core to core, and core to perimeter aluminum extrusion frame in the repair of durable rigidwall relocatable structures. The adhesive shall be suitable for forming bonds that will withstand exposure to temperatures from −54 °C to 93 °C (−65 °F to 199 °F) and high relative humidity and will also withstand the combinations of stress, temperature, and relative humidity that are expected to be encountered in service. The adhesive shall also be suitable for the bonding of panel inserts and edge attachments. 1.2 The values stated in SI units are to be regarded as standard where only SI units are given, or where SI units are given first followed by inch-pound units; where inch-pound units are given first followed by SI units, the inch-pound units are to be regarded as the standard. 1.3 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 6.1 Adhesives used in the repair of sandwich panels for durable, rigidwall, relocatable structures must have a combination of mechanical property levels and environmental resistance that will ensure long-term durability of the adhesive bonds when exposed to severe climatic exposures. In addition, these adhesives must have processability characteristics that permit their use in a variety of repair scenarios and environments. 6.2 This specification defines those characteristics that are required of adhesives to be used in the repair of sandwich panels for durable, rigidwall, relocatable structures.