1.1 本试验方法包括通过使用具有第三点荷载的简支梁测定水泥土的弯曲强度。 注1: 有关水泥土试样的成型方法，请参阅规程 D1632 . 1.2 单位- 以国际单位制或英寸-磅单位表示的数值应单独视为标准值。每个系统中规定的值不一定是精确的等价物；因此，为确保符合本标准，每个系统应独立使用，且两个系统的值不得组合。国际单位制用括号表示。 1.2.1 当处理英寸磅单位时，使用英寸磅单位的重力系统。在这个系统中，磅（lbf）表示力（重量）的单位，而质量的单位是段塞。除非涉及动态（F=ma）计算，否则未给出合理化的段塞单元。 1.3 所有观察值和计算值应符合实践中确定的有效数字和舍入准则 D6026 . 1.3.1 用于指定如何在标准中收集/记录或计算数据的程序被视为行业标准。此外，它们代表了通常应保留的有效数字。使用的程序不考虑材料变化、获取数据的目的、特殊目的研究或用户目标的任何考虑因素；通常的做法是增加或减少报告数据的有效位数，以与这些考虑因素相称。考虑工程设计分析方法中使用的有效数字超出了本标准的范围。 1.4 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 本试验方法用于测定水泥土的抗弯强度。弯曲强度在路面设计中非常重要，可用于确定路面层的厚度。 注2: 本标准产生的结果的质量取决于执行该标准的人员的能力，以及所用设备和设施的适用性。符合实践标准的机构 D3740 通常认为能够胜任和客观的测试/采样/检查等。本标准的用户应注意遵守惯例 D3740 本身并不能保证可靠的结果。可靠的结果取决于许多因素；实践 D3740 提供了一种评估其中一些因素的方法。

1.1 This test method covers the determination of the flexural strength of soil-cement by the use of a simple beam with third-point loading. Note 1: For methods of molding soil-cement specimens, see Practice D1632 . 1.2 Units— The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. The SI units are presented in brackets. 1.2.1 The gravitational system of inch-pound units is used when dealing with inchpound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F = ma) calculations are involved. 1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026 . 1.3.1 The procedures used to specify how data are collected/recorded or calculated in the standard are regarded as industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This test method is used to determine the flexural strength of soil-cement. Flexural strength is significant in pavement design and can be used to determine the thickness of pavement layers. Note 2: The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.