1.1 本测试方法规定了滑雪板在捆绑引导系统中的基本要求（见 3.1.2 ); 以下称为滑雪板绑定步骤。 1.2 本测试方法适用于成人和儿童的跨步滑雪板固定。这种装订系统利用机械联锁机制，系统的联锁机制将针对特定的制造商。不同系统之间的兼容性不是预期的，因此引导和绑定的每个潜在组合都需要测试。 1.3 关于与滑雪板固定器接口的滑雪板靴，请参见ISO 11634。 1.4 关于滑雪板固定，请参见ISO 14790。 1.5 关于为软靴制作的滑雪板绑带，请参见ISO 14573。 1.6 关于滑雪板跨步绑定，请参见ISO 15344。 1.7 本标准不涉及具有可编程释放模式的滑雪板固定器应如何或在何种情况下以预期模式释放，也不涉及滑雪板固定的任何可编程释放方式的安全性、可取性或有效性； 必须在禁用发布模式或将其调整到最高发布值的情况下，对此类与此标准的绑定进行任何测试。 1.8 本标准并不旨在解决与其使用相关的所有安全问题（如果有的话）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践，并确定监管限制的适用性。 1.9 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 =====意义和用途====== 4.1 本测试方法描述了评估步骤所需的步骤- 滑雪板捆绑系统功能。该测试方法包括一系列实验室测试，评估对静态和动态载荷的抵抗力、在寒冷和结冰条件下的功能、冲击和疲劳行为以及潜在假阳性释放的评估。所有测试都必须通过。 4.2 防尘套上所有可能的应变都可以归因于一个扭矩 M 一种力量 F 每个轴上都有 十、 , Y , Z 坐标系（参见 图1 ). 坐标的原点被认为位于踝关节的中心，该中心距离足底表面约100毫米，距离脚跟后部约80毫米。 图1 扭矩和力量 4.3 图中所示的扭矩和力 图1 是积极的。在相反方向上作用的相应参数被赋予负号。 箭头表示滑雪板靴运动的旋转方向。

1.1 This test method specifies the essential requirements for a snowboard step-in binding—boot system (see 3.1.2 ); hereafter referred to as step-in snowboard bindings. 1.2 This test method is applicable to step-in snowboard bindings for adults and children. This type of binding system utilizes a mechanical interlocking mechanism, and the interlock mechanism of the system will be specific to the particular manufacturer. Compatibility between different systems is not expected or anticipated thus each potential combination of boot and binding requires testing. 1.3 For snowboard boots interfacing with ski binding, see ISO 11634. 1.4 For snowboard plate bindings, see ISO 14790. 1.5 For snowboard strap bindings made for soft boots, see ISO 14573. 1.6 For snowboard step-in bindings, see ISO 15344. 1.7 This standard does not address how or under what circumstances a snowboard binding with programmable release modes should release in its intended modes nor does it address the safety, desirability, or efficacy of any programmable release mode for snowboard bindings; any testing of such bindings to this standard must be performed with the release modes disabled or adjusted to their highest release value. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 This test method describes the steps required to evaluate a step-in snowboard binding system function. The test method consists of a series of laboratory tests that evaluate resistance to static and dynamic loading, function under cold and icy conditions, impact and fatigue behavior and assessment of potential false positive release. All tests must be passed. 4.2 All possible strains on the boot can be attributed to one torque M and one force F each on every axis X , Y , Z of a system of coordinates (see Fig. 1 ). The point of origin of the coordinates is agreed to be in the center of the ankle joint which is located approximately 100 mm from the plantar surface and 80 mm from the back of the heel. FIG. 1 Torques and Forces 4.3 The torques and forces illustrated in the drawing in Fig. 1 are positive. The corresponding parameters acting in opposite direction are given negative signs. The arrowheads indicate the sense of rotation of the snowboard boot movement.