1.1 本性能规范涵盖梭织衬衫、连衣裙、礼服衬衫和运动衬衫的面料。 1.2 本性能规范不适用于衬布用机织物。 1.3 这些要求适用于与织物方向相关的属性的长度和宽度方向。 1.4 当织物需要特殊处理时，将描述为该材料开发的特定方法，此类特殊测试将优先于这些一般要求。 1.5 以下预防性警告仅适用于本性能规范中描述的测试方法 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践，并确定监管限制的适用性。 1.6 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《国际标准、指南和建议制定原则决定》中确立的国际公认标准化原则制定的。 =====意义和用途====== 4.1 用于此最终用途的织物应满足中列出的所有要求 表1 . （A） 有多种方法可用于测量断裂强度、撕裂强度和色牢度。这些方法不能互换使用，因为它们之间可能没有整体相关性（请参见 注2 和 注3 ). （B） 看见 注释5 . 4.2 应该认识到，织物可以利用几乎无限数量的结构变量组合（例如。 g、 、纤维类型、纤维百分比、纱线捻度、纱线数、经纱和纬纱数、化学和机械整理）。此外，时尚或美学要求最终消费者可能会发现由不符合以下所有要求的织物制成的可接受物品 表1 . 4.2.1 因此，没有单一的性能规范可能适用于可用于此最终用途的所有各种织物。 4.3 特定特性和测试方法的用途和意义在指定测试方法的适当章节中讨论。

1.1 This performance specification covers fabrics for woven blouses, dresses, dress shirts, and sport shirts. 1.2 This performance specification is not applicable to woven fabrics used for interlinings. 1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.4 When a fabric requires special treatment, specific methods will be described as they are developed for that material, and such special tests will have precedence over these general requirements. 1.5 The following precautionary caveat pertains only to the test methods described in this performance specification . This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 Fabrics intended for this end-use should meet all of the requirements listed in Table 1 . (A) There is more than one method that can be used to measure breaking strength, tearing strength and colorfastness. These methods cannot be used interchangeably since there may be no overall correlation between them (see Note 2 and Note 3 ). (B) See Note 5 . 4.2 It should be recognized that fabrics can be produced utilizing an almost infinite number of combinations of construction variables (e.g., type of fibers, percentage of fibers, yarn twist, yarn number, warp and pick count, chemical and mechanical finishes). Additionally, fashion or aesthetics dictate that the ultimate consumer may find acceptable articles made from fabrics that do not conform to all of the requirements in Table 1 . 4.2.1 Hence, no single performance specification can possibly apply to all the various fabrics that could be utilized for this end-use. 4.3 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.