1.1 本规范规定了设备的要求，旨在解决五岁及以下儿童因意外跌落打开的窗户而造成的伤亡风险。 1.2 本规范不旨在满足《美国残疾人法案》（ADA）的独特要求。 1.3 本规范适用于车窗防坠落装置，包括用于可操作车窗的车窗开启控制装置（WOCD）、车窗防坠落屏风和防坠落车窗护罩，包括用于紧急逃生（出口）和救援（入口）的装置。 注1: 单独的安全规范，安全规范 F2006年 ，包括安装在75英尺以上的非紧急逃生（出口）和救援（入口）窗口的防坠落装置 6. （23 m），因为这些高度的窗户超出了目前使用的救援梯的范围。 1.4 依赖窗户防坠落装置供应商的测试报告的窗户制造商应验证在其特定窗户产品操作器类型上安装的窗户防坠落装置（由窗户制造商在窗户装运前安装或由窗户制造商作为现场安装套件提供）是否符合本标准。 1.5 不允许部分遵守本标准。为了声称符合本标准，必须满足本标准中的所有适用要求。 1.6 以英寸-磅为单位的数值应视为标准值。括号中给出的值是到国际单位制的数学转换，仅供参考，不被视为标准值。 1.7 本标准无意解决与其使用相关的所有安全问题（如有）。本标准的用户有责任制定适当的安全、健康和环境实践，并在使用前确定监管限制的适用性。 1.8 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。

1.1 This specification establishes requirements for devices intended to address the risk of injury and death associated with accidental falls through open windows by children five years old and younger. 1.2 This specification is not intended to meet the unique requirements of Americans With Disabilities Act (ADA). 1.3 This specification applies to window fall prevention devices, including window opening control devices (WOCDs), window fall prevention screens, and fall prevention window guards, that are to be used on operable windows, including those that are designated for emergency escape (egress) and rescue (ingress). Note 1: A separate safety specification, Safety Specification F2006 , covers window fall prevention devices for non-emergency escape (egress) and rescue (ingress) windows in installations more than 75 ft 6 (23 m) above ground level in multiple family dwelling buildings since windows at these heights are beyond the reach of rescue ladders currently in use. 1.4 Window manufacturers who rely on a test report from the supplier of the window fall prevention device shall verify that the installation of the window fall prevention device (either installed by the window manufacturer prior to shipping of the window or provided by the window manufacturer as a field installed kit) on their specific window product operator type complies with this standard. 1.5 Partial compliance to this standard is not permitted. In order to claim compliance to this standard, all of the applicable requirements in the standard must be met. 1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.7 This standard does not purport to address all safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and to determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.