1.1 本试验方法用于在详细规范中规定的荷载下24小时进行长期压痕试验后，确定未安装弹性地板覆盖物的恢复性能。报告值，残余压痕，是指移除规定载荷后24小时剩余的凹陷深度。 1.2 本试验方法旨在评估出厂地板覆盖物，而非评估已安装地板覆盖物的性能。 1.3 本试验方法不适用于评估弹性地板覆盖物在高于第节所述精度和偏差声明中所列载荷的情况下的长期抗压痕性能或恢复性能，或两者兼而有之 10 . 1.3.1 在250 psi以上的负载下进行测试不在本测试方法的范围内。 1.4 使用除第节所列精确板以外的任何其他压头板进行试验 4. 超出了本测试方法的范围。 1.5 以英寸-磅单位表示的数值应视为标准值。括号中给出的数值是国际单位制的数学转换，仅供参考，不被视为标准。 1.6 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践，并确定监管限制的适用性。 1.7 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 =====意义和用途====== 3.1 该测试方法是一种有意义的测试，用于确定未安装弹性地板覆盖物的压痕恢复特性。 3. 3.2 本试验方法仅用于确定是否符合ASTM弹性地板覆盖物委员会F06管辖的弹性地板产品规范中规定的静载荷要求（如适用）。 3.3 由于测试是在未安装的地板上进行的，因此测试结果并不是地板覆盖物安装性能的指标。 3.

1.1 This test method is intended for use in determining the recovery properties of uninstalled resilient floor covering after long-term indentation test, 24 h under the load specified in the detail specification. The reported value, residual indentation, is the depth of the depression remaining 24 h after removal of the specified load. 1.2 This test method is intended to evaluate ex-factory floor covering and is not intended to evaluate the performance of installed floor coverings. 1.3 This test method is not intended for use in evaluating the long-term indentation resistance or recovery properties, or both, of resilient floor coverings at loads above those listed in the Precision and Bias statement as described in Section 10 . 1.3.1 Testing at loads above 250 psi is outside the scope of this test method. 1.4 Testing with any other indentor plate other than the exact plates listed in Section 4 is outside the scope of this test method. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 3.1 This test method is a meaningful test for determining the indentation recovery properties of uninstalled resilient floor covering. 3 3.2 This test method is intended solely for the purpose of determining compliance, where applicable, with static load requirements set forth in resilient flooring product specifications under the jurisdiction of ASTM Committee F06 on Resilient Floor Coverings. 3.3 As testing is conducted on uninstalled flooring, results are not an indicator of the floor covering's installed performance. 3