1.1 本规范涵盖了对无缝针织服装（包括背心、内裤、吊带、腰带和泳衣）的重要特定性能特征的评估。 1.2 以下安全隐患警告仅适用于本性能规范中描述的测试方法: 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.3 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ===意义和用途====== 4.1 根据买方和供应商之间的共同协议，用于该最终用途的无缝针织服装应符合 表1 本规范。 （A） 看见 注4 。 4.2 人们认识到，出于时尚或美观的目的，由这些织物制成的物品的最终消费者可能会发现不符合 表1 。因此，中的一个或多个要求 表1 可通过买方和供应商之间的共同协议进行修改。 4.2.1 在这种情况下，任何对规范的引用都应规定:“本产品符合ASTM规范XXXX，但以下特性除外。” 4.3 如果没有- 买方和供应商已达成采购协议，如有争议 表1 仅用作指南。如中所述 4.2 ，消费者的最终需求决定了特定产品的不同性能参数。 4.4 特定性能和测试方法的用途和重要性在指定测试方法的适当章节中进行了讨论。

1.1 This specification covers the evaluation of specific performance characteristics of importance in seamless knit garments, including camisoles, panties, slips, girdles and swimwear. 1.2 The following safety hazards caveat pertains only to the test methods described in this performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 Upon mutual agreement between the purchaser and the supplier, seamless knit garments intended for this end use should meet all of the requirements listed in Table 1 of this specification. (A) See Note 4 . 4.2 It is recognized that, for purposes of fashion or aesthetics, the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements listed in Table 1 . Therefore, one or more of the requirements in Table 1 may be modified by mutual agreement between the purchaser and the supplier. 4.2.1 In such cases, any references to the specifications should specify that: “This product meets ASTM specifications XXXX except for the following characteristic(s).” 4.3 Where no pre-purchase agreement has been reached between the purchaser and supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2 , ultimate consumer demands dictate varying performance parameters for a particular product. 4.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.