1.1 这些测试方法包括压敏粘合剂性能的测定。这些测试方法适用于那些在与另一表面接触时迅速形成可测量强度的粘合剂。粘接力可以测量为在仅等于压敏物品（例如，胶带、标签、贴纸等）在1英寸上的重量的载荷下使粘合剂与被粘物接触后不久在界面处分离所需的力。 2. 接触面积。 1.2 包括以下测试方法: 1.2.1 试验方法A （使用拉伸试验机），以及 1.2.2 试验方法B （使用回路粘性测试仪）。 1.3 由于压敏胶带的行业标准宽度为1英寸，所以以英寸-磅单位表示的值应视为标准。括号中给出的数值是国际单位制的数学转换，仅供参考，不被视为标准。 1.4 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践，并确定监管限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 =====意义和用途====== 5.1 这些测试方法提供了粘合剂压敏粘性的定量测量。 图1 回路定位测试夹具1 图2 回路定位测试夹具2 图3 测试期间的回路粘性样品 5.2 这些测试方法旨在测量粘合剂块的粘性。 给定粘合剂的粘性随背衬而变化（通常，背衬越硬，值越高）。 5.3 这些测试方法适用于质量控制和研究目的。 5.4 试验方法A （使用拉伸试验机）使用7英寸的试样条。（175 mm）长。FINAT FTM 9“Quick Stick”粘结测量试验和TLMI L-IB2拉伸试验机回路粘结试验也使用相同长度的试样条。 5.5 试验方法B （使用回路粘性测试仪）使用5英寸的试样条。（125 mm）长。这是唯一一条适合于环粘性测试仪的试样条。 5.6 如果粘合剂尚未以其他方式涂覆，这些测试方法包括使用透明的2密耳（0.05毫米）聚酯（PET）薄膜背衬进行样品制备。使用其他背衬材料会改变待测试样的性能。

1.1 These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface. Tack force may be measured as the force required to separate the adhesive from the adherend at the interface shortly after they have been brought into contact under a load equal only to the weight of the pressure-sensitive article (for example, tape, label, sticker, etc.) on a 1 in. 2 contact area. 1.2 The following test methods are included: 1.2.1 Test Method A (using Tensile Tester), and 1.2.2 Test Method B (using Loop Tack Tester). 1.3 The values stated in inch-pound units are to be regarded as the standard because the industry standard width for pressure-sensitive tape is 1 inch. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 These test methods provide a quantitative measure of the pressure-sensitive tack property of an adhesive. FIG. 1 Loop Tack Test Fixture 1 FIG. 2 Loop Tack Test Fixture 2 FIG. 3 Loop Tack Sample During Test 5.2 These test methods are designed to measure the tack property of the adhesive mass. The tack of a given adhesive varies depending on the backing (generally, stiffer backings lead to higher values). 5.3 Theses test methods are suitable for quality control and research purposes. 5.4 Test Method A (using Tensile Tester) makes use of a specimen strip 7 in. (175 mm) in length. Both the FINAT FTM 9 “Quick Stick” Tack Measurement Test and the TLMI L-IB2 Tensile Tester Loop Tack Test also use a specimen strip of that length. 5.5 Test Method B (using Loop Tack Tester) makes use of a specimen strip five in. (125 mm) in length. That is the only length specimen strip that fits properly in the loop tack tester. 5.6 If the adhesive is not already otherwise coated, these test methods incorporate the use of a clear 2 mil (0.05 mm) polyester (PET) film backing for specimen preparation. Use of other backing materials changes performance of the specimen to be tested.