1.1 本规范旨在适用于作为现浇钢筋混凝土梁永久模板的隔热混凝土模板（ICF）系统；过梁；外部和内部、地面上和地面下承重墙和非承重墙；基础；和挡土墙。本规范仅限于具有统一整体混凝土芯的ICF系统。 1.2 本规范所涵盖的产品包括模压发泡聚苯乙烯（EPS）绝缘板，这些板通过交叉连接件连接，形成ICF系统。 1.3 本规范确定了适用于确定ICF系统作为原位混凝土成型系统的主要功能性能的测试方法。本规范涵盖的ICF系统的使用应受到涉及防火性能、结构性能或两者的建筑规范的监管。 材料的防火性能应通过适当的管理文件制定的标准防火试验方法来解决。必须根据适当的规范要求，通过混凝土结构设计来解决结构性能问题。 1.4 制造程序的细节超出了本规范的范围。 1.5 以国际单位表示的数值视为标准值。括号中给出的值是以英寸-磅为单位的数学转换，仅供参考，不被视为标准值。若要转换为本规范中包含的公制单位以外的其他公制单位，请参阅 IEEE/ASTM标准 硅 10 . 1.6 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.7 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。

1.1 This specification is intended to apply to Insulating Concrete Form (ICF) Systems that will act as permanent formwork for cast-in-place reinforced concrete beams; lintels; exterior and interior, above and below grade bearing and non-bearing walls; foundations; and retaining walls. The specification is restricted to ICF Systems with a resultant uniform monolithic concrete core. 1.2 Products covered by the specification consists of molded expanded polystyrene (EPS) insulation panels that are connected by cross ties to form the ICF System. 1.3 This specification identifies test methods appropriate for establishing ICF System performance in their primary function as a stay in place concrete forming system. The use of ICF Systems covered by this specification shall be regulated by building codes that address fire performance, structural performance or both. The fire performance of the material shall be addressed through standard fire test methods established by the appropriate governing documents. The structural performance must be addressed through design of concrete structures in accordance with the appropriate Code requirements. 1.4 Details of manufacturing procedures are beyond the scope of this specification. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. For conversion to metric units other than those contained in this specification, refer to IEEE/ASTM SI 10 . 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.