1.1 本规范规定了室外健身设备的设计和制造参数，如 3.1.30 . 1.2 这些健身产品将在无监督的室外环境中使用，并永久固定。 1.2.1 本规范的目的是仅规定户外健身设备及其安装的要求，而不是产品安装的设施或地面的设计。 1.3 本标准中规定的规范旨在将重伤的可能性降至最低。 1.3.1 本标准中规定的规范适用于13岁及以上的个人在无监督环境中使用的户外健身设备。 1.4 以国际单位制（公制）单位表示的值应视为标准值。括号中的值仅供参考。 1.5 一般测量、公差和换算: 1.5.1 本规范的一般公差（除非另有规定）如下: 维 容忍 X毫米（X英寸） ±13.0毫米（0.5英寸） 十、 X毫米（X.X英寸） ±1.3毫米（0.05英寸） 十、 XX毫米（X.XX英寸） ±.0.130毫米（0.005英寸） 1.5.2 即使使用了大于、小于、最小或最大等术语，这些公差仍适用于尺寸。 1.6 本标准将与试验方法一起使用 F2571 和规格 F2276页 . 如果本规范中未涉及设计或安装问题，则本规范的适用要求 F2276页 应使用。 1.6.1 本标准优先于规范 F2276页 和试验方法 F2571 在本文件所述领域。 1.7 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.8 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。

1.1 This specification establishes parameters for the design and manufacture of outdoor fitness equipment as defined in 3.1.30 . 1.2 It is intended that these fitness products will be used in an unsupervised outdoor setting or environment and will be permanently anchored. 1.2.1 It is the intent of this specification to only specify requirements for outdoor fitness equipment and its installation and not the design of the facility or grounds on which the products are to be installed. 1.3 The specifications set forth in this standard are intended to minimize the likelihood of serious injuries. 1.3.1 The specifications set forth in this standard are for outdoor fitness equipment intended for use in an unsupervised setting by individuals age 13 and older. 1.4 The values stated in SI (metric) units are to be regarded as standard. The values in parentheses are for information only. 1.5 General Measures, Tolerances, and Conversions: 1.5.1 The general tolerances for this specification (unless otherwise specified) are as follows: Dimension Tolerance X mm (X in.) ± 13.0 mm (0.5 in.) X.X mm (X.X in.) ±1.3 mm (0.05 in.) X.XX mm (X.XX in.) ±.0.130 mm (0.005 in.) 1.5.2 These tolerances still apply to a dimension even when terms like greater than, less than, minimum, or maximum are used. 1.6 This standard is to be used in conjunction with Test Methods F2571 and Specification F2276 . If a design or installation concern is not addressed in this specification then the applicable requirements of Specification F2276 shall be used. 1.6.1 This standard takes precedence over Specification F2276 and Test Methods F2571 in areas that are addressed in this document. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.