1.1 本试验方法包括使用具有固定表面（台板）、在规定力下的圆形压脚并能够在台板上方垂直移动的测厚仪测定成品水平绒头纱地板覆盖物的绒头厚度。 1.2 本试验方法仅适用于毛簇高度小于0.25 in.（6 mm）的成品水平毛圈、切绒和切绒毛圈结构。 1.3 以英寸磅为单位的数值应视为标准。 括号中给出的值是国际单位制的数学转换，仅供参考，不被视为标准。 1.4 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ====意义和用途====== 5.1 水平绒头纱地板覆盖物绒头厚度的确定有助于绒头纱地面覆盖物生产过程中的质量和成本控制。绒头纱地板覆盖物的绒头厚度的变化可能会影响其外观和性能。这种测试方法被认为是令人满意的商业货物验收测试，因为目前对实验室间精度的估计是可以接受的，而且这种测试方法通常用于验收测试。 5.2 如果两个实验室（或多个实验室）报告的测试结果之间存在实际意义上的差异，则应使用主管的统计协助进行比较测试，以确定它们之间是否存在统计偏差。作为最低要求，使用尽可能同质的样本进行此类比较测试，这些样本与在初始测试期间产生不同结果的样本来自同一批次的材料，并以相同数量随机分配给每个实验室。 应使用未配对数据的统计测试对相关实验室的测试结果进行比较，这是在测试系列之前选择的概率水平。如果发现偏差，则必须找到并纠正其原因，或者必须根据已知偏差调整该材料的未来测试结果。

1.1 This test method covers the determination of pile thickness of finished level pile yarn floor covering using a thickness measuring instrument having a stationary surface (platen), a circular pressure foot under specified force, and capable of being moved vertically above the platen. 1.2 This test method is applicable only to finished level loop, cutpile and cut & loop constructions with tuft heights less than 0.25 in. (6 mm). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 The determination of pile thickness of level pile yarn floor covering is useful in quality and cost control during the manufacture of pile yarn floor covering. The appearance and performance may be affected by changes in pile thickness of pile yarn floor coverings. This test method is considered satisfactory for acceptance testing of commercial shipments because current estimates of between laboratory precision are acceptable, and this test method is commonly used in the trade for acceptance testing. 5.2 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use the samples for such comparative tests that are as homogenous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, a probability level chosen prior to the testing series. If a bias is found either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.