BS EN ISO 8041-1:2017规定了设计仪器的性能规范和公差限值 测量振动值，以评估人类对振动的反应。它包括 模式评估或验证、定期验证和现场检查的要求，以及 现场检查用振动校准器规范。本文件中规定的振动仪器可以是单个仪器，也可以是 仪器或基于计算机的采集和分析系统。本文件中规定的振动仪器用于测量一个或多个振动 应用，例如:手传振动（见ISO 5349-1）；全身振动（参见ISO 2631-1、ISO 2631-2和ISO 2631- 4);低频全身振动，频率范围为0.1 Hz至0.5 Hz（见ISO 2631-1）。振动仪器可以根据一个或多个频率进行测量 每个应用程序中定义的权重。本文件中定义了三个性能测试级别:a）模式评估或验证:1）模式评估，即根据本文件中定义的规范对仪器进行全面测试 文件2） 一次性仪器的验证，即单个振动测量的有限测试集 系统是否符合本文件中定义的相关规范；b） 定期验证，即一组中间测试，旨在确保仪器保持稳定 在要求的性能规范范围内； c） 现场检查，即表明仪器可能被损坏所需的最低测试水平 在要求的性能规格范围内运行。交叉引用:ISO 5347-22:1997ISO 2631-2:2003IEC 61000-4-6:2013 ED4ISO 5347-13:1993（R04）ISO 5347-8:1993（R04）ISO 16063-12:2002ISO 16063-1:1998IEC 61000-4-2:2008 Ed 2CISPR 22:2008 Ed 6ISO 5349-1:2001 Ed 1ISO 5347-19:1993（R04）ISO 16063-21:2003ISO 2631-1:1997 Ed 2ISO 5347-2:2:2:2005IEC 61000-6-2:2005IEC 61000-4-3:2008 Ed 6ISO 5349-1-16:20035347-15:1993（R04）ISO 5347-17:1993（R04）ISO 16063-11:1999（R10）ISO 2631-4:2001 Ed 1ISO/IEC指南98-3:2008 Ed 1ISO 5347-3:1993ISO 5347-9:1993 ISO 2041:2009 Ed 3ISO 5805:1997ISO 10326-1:2016IEC 61260-1:2014ISO 1683: 2015年ED3IEC 61672-1:2013IEC 60529:1989 Cons Ed 2-1ISO/IEC指南99:2007ISO 5348:1998（R04）CISPR 16-1-1:2015ISO/TR 19664:2017DIN 45662购买本文件时提供的所有当前修订版均包含在购买本文件中。

BS EN ISO 8041-1:2017 specifies the performance specifications and tolerance limits for instruments designed to measure vibration values, for the purpose of assessing human response to vibration. It includes requirements for pattern evaluation, or validation, periodic verification and in situ checks, and the specification of vibration calibrators for in situ checks.Vibration instruments specified in this document can be single instruments, combinations of instrumentation or computer-based acquisition and analysis systems.Vibration instruments specified in this document are intended to measure vibration for one or more applications, such as the following:hand-transmitted vibration (see ISO 5349-1);whole-body vibration (see ISO 2631-1, ISO 2631-2 and ISO 2631-4);low-frequency whole-body vibration in the frequency range from 0,1 Hz to 0,5 Hz (see ISO 2631-1).Vibration instruments can be designed for measurement according to one or more of the frequency weightings defined within each of these applications.Three levels of performance testing are defined in this document:a) pattern evaluation or validation:1) pattern evaluation, i.e. a full test of the instrument against the specifications defined in this document;2) validation of one-off instruments, i.e. a limited set of tests of an individual vibration measuring system against the relevant specifications defined in this document;b) periodic verification, i.e. an intermediate set of tests designed to ensure that an instrument remains within the required performance specification;c) in situ checks, i.e. a minimum level of testing required to indicate that an instrument is likely to be functioning within the required performance specification.Cross References:ISO 5347-22:1997ISO 2631-2:2003IEC 61000-4-6:2013 ED4ISO 5347-13:1993 (R04)ISO 5347-8:1993 (R04)ISO 16063-12:2002ISO 16063-1:1998IEC 61000-4-2:2008 Ed 2CISPR 22:2008 Ed 6ISO 5349-1:2001 Ed 1ISO 5347-19:1993 (R04)ISO 16063-21:2003ISO 2631-1:1997 Ed 2ISO 5347-2:1993IEC 61000-6-2:2005IEC 61000-4-3:2006 Cons Ed 3-2ISO 16063-45:2017ISO 5347-16:1993 (R04)ISO 16063-13:2001ISO 5347-15:1993 (R04)ISO 5347-17:1993 (R04)ISO 16063-11:1999 (R10)ISO 2631-4:2001 Ed 1ISO/IEC GUIDE 98-3:2008 Ed 1ISO 5347-3:1993ISO 5347-9:1993 ISO 2041:2009 Ed 3ISO 5805:1997ISO 10326-1:2016IEC 61260-1:2014ISO 1683:2015 ED3IEC 61672-1:2013IEC 60529:1989 Cons Ed 2-1ISO/IEC Guide 99:2007ISO 5348:1998 (R04)CISPR 16-1-1:2015ISO/TR 19664:2017DIN 45662All current amendments available at time of purchase are included with the purchase of this document.