1.1 本性能规范涵盖由任何纺织纤维或用于紧身胸衣、腰带或其组合的纤维混合物组成的机织物和针织物。 1.2 本性能规范不适用于针织或机织紧身胸衣-腰带组合织物、针织蕾丝织物和用于衬布的织物。 1.3 这些要求适用于与每个织物方向相关的属性的长度和宽度方向。 1.4 本标准并非旨在解决与其使用相关的所有安全问题（如有）。 本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 经买方和供应商同意，用于该最终用途的织物应符合 表1 性能规范。 5.2 人们认识到，出于时尚或美学的目的，这些面料制成的物品的最终消费者可能会发现可接受的面料不符合本标准的所有要求 表1 . 因此，中列出的一个或多个要求 表1 可在买方和供应商之间达成协议后进行修改。 5.2.1 在这种情况下，对本规范的任何引用应规定: “这种织物符合ASTM规范 D4116 除以下特征外。” 5.3 如果买方和供应商之间未达成预采购协议，如果存在争议，则应满足以下要求: 表1 仅供参考。如中所述 5.2 最终消费者需求决定了任何特定风格的面料的不同性能参数。 5.4 特定属性和方法的用途和意义在指定方法的适当章节中进行了讨论。

1.1 This performance specification covers woven and knitted fabrics composed of any textile fiber or mixture of fibers used in corsets, girdles or a combination of the same. 1.2 This performance specification is not applicable to knitted or woven corset-girdle-combination fabrics, to knitted lace fabrics, and to fabrics used for interlinings. 1.3 These requirements apply to the length and width directions for those properties where each fabric direction is pertinent. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 Upon agreement between the purchaser and the supplier, fabrics intended for this end use should meet all the requirements listed in Table 1 of this performance specification. 5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1 . Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the supplier. 5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4116 except for the following characteristic(s).” 5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2 , ultimate consumer demands dictate varying performance parameters for any particular style of fabric. 5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.