BS EN 15048-1:2016规定了非重载结构螺栓连接用螺栓组件的一般要求。符合本欧洲标准的螺栓组件设计用于剪切和/或拉伸载荷的结构螺栓连接。根据本欧洲标准，螺栓组件的预期用途为结构金属工程。它适用于螺栓（当螺栓部分螺纹、螺钉、螺柱和螺柱螺栓 （综合考虑）以及由碳钢、合金钢、不锈钢或铝制成的螺母或 具有以下性能等级的铝合金: 碳钢或合金钢制螺栓:4.6、4.8、5.6、5.8、6.8、8.8、10.9（根据 EN ISO 898-1）；碳钢或合金钢制成的螺母:5、6、8、10、12（符合EN ISO 898-2）；奥氏体不锈钢制螺栓:50、70、80（符合EN ISO 3506-1）；奥氏体不锈钢制螺母:50、70、80（符合EN ISO 3506-2）；铝或铝合金制成的螺栓:AL1至AL6（符合EN 28839）；铝或铝合金制成的螺母:AL1至AL6（符合EN 28839）。本欧洲标准适用于尺寸为ISO公制粗牙螺纹的螺栓组件 根据EN 1090-2，M12至M39用于钢结构，M5至M39用于 符合EN 1090-3的铝或铝合金结构。使用的螺纹尺寸大于 如果满足本标准的所有适用要求，则不排除M39。警告-本协调标准仅涵盖螺栓组件:未按照EN 15048-2作为螺栓组件组装批次的一部分进行测试的单独螺栓或螺母不适用 受本协调标准管辖，且不能使用CE标记。注1:4.8、5.8和6.8类财产可能会受到使用限制。附注2高- 符合EN 14399-1要求的预加载强度结构螺栓组件不在本欧洲标准的范围内，但也适用于非预加载结构螺栓。注3:铝或铝合金制成的螺栓和螺母不适用于钢结构，见EN 1090-2。符合本欧洲标准的螺栓组件不得焊接。本欧洲标准不包括铁路扣件。交叉引用:EN 1090-2EN 15048-2EN 28839ISO 8839EN ISO 225ISO 225EN ISO 898-1ISO 898-1EN ISO 898-2ISO 898-2EN ISO 3506-1ISO 3506- 1EN ISO 3506-2ISO 3506-2EN ISO 4759-1ISO 4759-1EN ISO 10684:2004ISO 10684:2004ISO 965-1ISO 965-2ISO 965-3ISO 965-4ISO 965-5305/2011/EUEN 1993-1-8EN 1999-1-1EN 14399-1EN ISO 9001ISO 9001EN 1090-3EN 10204购买本文件时可提供的所有当前修订版。

BS EN 15048-1:2016 specifies the general requirements for bolting assemblies for nonpreloaded structural bolting. Bolting assemblies in accordance with this European Standard are designed to be used in structural bolting connections for shear and/or tensile loading.The intended use of bolting assemblies in accordance with this European standard is structural metallic works.It applies to bolts (the term used when bolts partially threaded, screws, studs and stud-bolts are considered all together) and nuts made of carbon steel, alloy steel, stainless steel or aluminium or aluminium alloy with the following property classes:bolts made of carbon steel or alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 (in accordance with EN ISO 898-1);nuts made of carbon steel or alloy steel: 5, 6, 8, 10, 12 (in accordance with EN ISO 898-2);bolts made of austenitic stainless steel: 50, 70, 80 (in accordance with EN ISO 3506-1);nuts made of austenitic stainless steel: 50, 70, 80 (in accordance with EN ISO 3506-2);bolts made of aluminium or aluminium alloy: AL1 to AL6 (in accordance with EN 28839);nuts made of aluminium or aluminium alloy: AL1 to AL6 (in accordance with EN 28839).This European Standard applies to bolting assemblies with ISO metric coarse pitch thread from sizes M12 to M39 for use in steel structures according to EN 1090-2, and from M5 to M39 for use in aluminium or aluminium alloy structures according to EN 1090-3. The use of thread sizes larger than M39 is not precluded provided all applicable requirements of this standard are met.WARNING - Only bolting assemblies are covered by this harmonized standard: separate bolts or nuts, not tested as part of an assembly lot of bolting assemblies in accordance with EN 15048-2, are not covered by this harmonized standard and cannot be CE marked.NOTE 1 The property classes 4.8, 5.8 and 6.8 may be subjected to limitations of use.NOTE 2 High-strength structural bolting assemblies for preloading which meet the requirements of EN 14399-1 are not within the scope of this European Standard but they are also suitable for use in non-preloaded structural bolting.NOTE 3 Bolts and nuts made of aluminium or aluminium alloys are not designed to be used in steel structures, see EN 1090-2.Bolting assemblies in accordance with this European Standard are not designed to be welded.Railway rail fasteners are not covered by this European Standard.Cross References:EN 1090-2EN 15048-2EN 28839ISO 8839EN ISO 225ISO 225EN ISO 898-1ISO 898-1EN ISO 898-2ISO 898-2EN ISO 3506-1ISO 3506-1EN ISO 3506-2ISO 3506-2EN ISO 4759-1ISO 4759-1EN ISO 10684:2004ISO 10684:2004ISO 965-1ISO 965-2ISO 965-3ISO 965-4ISO 965-5305/2011/EUEN 1993-1-8EN 1999-1-1EN 14399-1EN ISO 9001ISO 9001EN 1090-3EN 10204All current amendments available at time of purchase are included with the purchase of this document.