1.1 本规范涵盖含98.00%的退火铝和铝合金箔 % 最小铝厚度为0.00025英寸。（0.0064 mm）至（但不包括）0.006 in。（0.15毫米）。合金（见 注1 )本规范涵盖的内容包括但不限于1100、1145、1235、8011、8079和8111，它们符合 6.1 和表1。除非买方另有规定，否则供应的合金应由生产商自行决定。 1.2 铝箔用于包装，包括食品处理和加工应用，需要柔性阻隔材料和其他一般应用。箔可用于供应或层压到其他材料，如纸或塑料膜。 1.3 有关本规范中包含新铝和铝合金的验收标准，请参阅 附件A1 . 1.4 以英寸-磅为单位的数值应视为标准值。括号中的SI值仅供参考。 1.5 以下预防性警告仅适用于本规范的试验方法部分: 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 注1: 在本规范中，术语的使用 合金 一般来说，包括铝以及铝合金。 注2: 如果买方指定了合金，则其名称应符合ANSI H35.1。等效的统一编号系统合金名称如所示 1.1 例如，根据惯例，A91100前面带有A9，用于铝1100 E527 . 1.6 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。

1.1 This specification covers annealed aluminum and aluminum-alloy foil containing 98.00 % minimum aluminum and in thicknesses 0.00025 in. (0.0064 mm) to, but not including, 0.006 in. (0.15 mm). Alloys (see Note 1 ) covered by this specification include, but are not limited to 1100, 1145, 1235, 8011, 8079, and 8111, which conform to the requirements of 6.1 and Table 1. Unless otherwise specified by the purchaser, the alloy to be supplied shall be left to the discretion of the producer. 1.2 The foil is for use in packaging, which includes food handling and processing applications, requiring flexible barrier materials, and other general applications. The foil may be used as supplied or laminated to other materials, such as paper or plastic films. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1 . 1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values in parentheses are for information only. 1.5 The following precautionary caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2: If the alloy is specified by the purchaser, its designation shall be in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those shown in 1.1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527 . 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.