1.1 本规范涵盖氯化聚氯乙烯（CPVC）螺纹80号管接头。包括对材料、工艺、尺寸和爆破压力的要求。 注1: 本规范涵盖的CPVC配件先前已包含在规范中 D2464 . 1.2 本规范所涵盖的产品仅用于分配与管道材料化学相容的加压液体。由于用压缩空气或其他压缩气体测试部件和系统的固有危险，一些制造商不允许对其产品进行气动测试。气动测试前，请咨询特定的产品/部件制造商，了解其特定的测试程序。 注2: 加压（压缩）空气或其他压缩气体含有大量储存的能量，如果系统因任何原因发生故障，这些能量会带来严重的安全隐患。 1.3 本规范的文本引用了提供解释材料的注释、脚注和附录。这些注释和脚注（不包括表和图中的注释和脚注）不应被视为规范的要求。 1.4 以英寸磅为单位的数值应视为标准。括号中给出的值是国际单位制的数学转换，仅供参考，不被视为标准。 1.5 以下安全隐患警告仅适用于试验方法部分，第节 8. ，本规范的: 本标准并不旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.6 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。

1.1 This specification covers chlorinated poly(vinyl chloride) (CPVC) threaded Schedule 80 pipe fittings. Included are requirements for materials, workmanship, dimensions, and burst pressure. Note 1: The CPVC fittings covered by this specification were covered previously in Specification D2464 . 1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which are chemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. Consult with specific product/component manufacturers for their specific testing procedures prior to pneumatic testing. Note 2: Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards should a system fail for any reason. 1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 8 , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.