BS EN ISO 17662:2016规定了设备的校准、验证和确认要求 用于控制制造过程中工艺变量的设备，以及用于焊接或焊接相关工艺的设备性能的控制 如果后续监测无法方便或经济地记录结果输出， 检查和测试。这涉及过程变量，影响目标和目标的适用性 尤其是成品的安全性。注1:本国际标准基于国际标准中规定的工艺变量清单 焊接工艺规范标准，尤其是但不限于ISO 15609- 系列 这些国际标准的未来修订可能会增加或删除所考虑的参数 需要详细说明。此外，关于校准要求，附录B中给出了一些指南；验证 以及作为焊接或相关工艺所用设备验收测试的一部分的验证。作为检验、测试、无损检测一部分的校准、验证和确认要求 或对最终焊接产品进行测量，以验证产品符合性 不在当前国际标准的范围内。本国际标准的主题仅限于校准、验证和确认 设备安装后，作为车间和现场操作的一部分进行维护和/或 活动需要强调的是，本国际标准与制造和安装无关 焊接设备的安装。指令中规定了对新设备的要求 以及必要的产品规范（标准）。附件C提供了其他各方参与校准、验证和确认时的信息 活动。交叉引用:ISO 669ISO 5171ISO 5172:2006ISO 5826ISO 3834-1ISO 3834-2ISO 3834-3ISO 3834-4ISO 4063ISO 8206ISO 9000ISO 10012ISO 14744-1ISO 14744-2ISO 14744-3ISO 14744- 4 ISO 14 14 ISO 14 14 ISO 14 14 14 ISO 14 14 14 14 14 14 14 14 14 14 14 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 ISO 14 14 14 14 14 14 14 14 14 14 14 14 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 04ISO 9001ISO 9004ISO/IEC指南99:2007包括购买时可用的所有当前修订版购买了这份文件。

BS EN ISO 17662:2016 specifies requirements for calibration, verification and validation of equipment used forcontrol of process variables during fabrication, andcontrol of the properties of equipment used for welding or welding allied processes where the resulting output cannot be readily or economically documented by subsequent monitoring, inspection and testing. This involves process variables influencing the fitness-for-purpose and in particular the safety of the fabricated product.NOTE 1 This International Standard is based on the lists of process variables stated in International Standards for specification of welding procedures, in particular, but not exclusively in the ISO 15609- series. Future revisions of these International Standards can result in addition or deletion of parameters considered necessary to specify.Some guidance is, in addition, given in Annex B as regards requirements for calibration; verification and validation as part of acceptance testing of equipment used for welding or allied processes.Requirements to calibrate, verify and validate as part of inspection, testing, non-destructive testing or measuring of final welded products performed in order to verify confirm product compliance are outside the scope of the present International Standard.The subject of this International Standard is limited to calibration, verification and validation of equipment after installation, as part of the workshops' and site operations for maintenance and/or operation.It needs to be stressed that this International Standard has nothing to do with manufacture and installation of equipment for welding. Requirements for new equipment are formulated in directives and product codes (standards), as necessary.Annex C provides information when other parties are involved in calibration, verification and validation activities.Cross References:ISO 669ISO 5171ISO 5172:2006ISO 5826ISO 3834-1ISO 3834-2ISO 3834-3ISO 3834-4ISO 4063ISO 8206ISO 9000ISO 10012ISO 14744-1ISO 14744-2ISO 14744-3ISO 14744-4ISO 14744-5ISO 14744-6ISO/TR 16060ISO/TR 18491IEC 62135-1IEC 62135-2EN 50505EN 60974-1ISO 6947ISO 14554-1ISO 14554-2ISO 14555ISO 15609-1ISO 15609-2ISO 15609-3ISO 15609-4ISO 15609-5ISO 15614-11ISO 15616-1ISO 15616-2ISO 15616-3ISO 15616-4ISO 15620ISO 17637ISO 22827-1ISO 22827-2EN 13134EN 50504ISO 9001ISO 9004ISO/IEC Guide 99:2007All current amendments available at time of purchase are included with the purchase of this document.