BS EN 1492-4:2000+A1:2008规定了与安全相关的要求，包括评级和测试方法 最大工作载荷为40吨的圆形吊索（在直吊中）和两腿、三腿和四腿圆形吊索 由聚酰胺、聚酯和聚丙烯制成的带或不带配件的组件。BS EN 1492-4:2000+A1:2008中涵盖的圆形吊索适用于一般用途的起重作业，即: 用于起吊不需要偏离要求、安全系数或安全系数的物体、材料或货物 WLL？这是规定的。本标准未涵盖的起重作业包括人员的起重，可能包括: 危险材料，如熔融金属和酸、玻璃板、裂变材料、核反应堆和 适用特殊条件的。符合BS EN 1492-4:2000+A1:2008的圆形吊索适用于以下场所使用和储存: 温度范围:a）聚酯和聚酰胺:-40 C至100 C，b）聚丙烯:-40 C至80 CBS EN 1492-4:2000+A1:2008不适用于以下所示类型的圆吊索:a）用于将货物固定或捆绑在托盘、平台或车辆上的圆吊索；b） 无填充的管状织带吊索。英国标准EN 1492- 4:2000+A1:2008阐述了将第4条中列出的危害降至最低的技术要求 在使用圆吊索时，如果按照说明和 制造商或授权代表给出的规范。交叉引用:EN 292-2:1991EN 292-2:1991/A1:1995EN 1050:1996prEN 1677-1:2000prEN 1677-2:2000prEN 1677-3:1998prEN 1677-4:1998prEN 1677-5:1998prEN 1677-6:1998EN 10002-2:1991EN 45012ISO/IEC指南62:1996EN ISO 9002:1994ISO 1833ISO 2076ISO 12480-198/37/EC98/79/EC2006/42/ECRPOROA: AMD 16577于2006年9月29日发布，MD 16577为勘误表。修正案，2009年6月。修订并替换BS EN 1492-2:2000

BS EN 1492-4:2000+A1:2008 specifies the requirements related to safety, including methods of rating and testing roundslings up to 40 tonnes working load limit (in straight lift) and two-, three-, and four-leg roundsling assemblies, with or without fittings, made of polyamide, polyester and polypropylene.The roundslings covered by BS EN 1492-4:2000+A1:2008 are intended for general purpose lifting operations, i.e. when used for lifting objects, materials or goods which require no deviations from the requirements, safety factors or WLL?s specified. Lifting operations not covered by this standard include the lifting of persons, potentially dangerous materials such as molten metal and acids, glass sheets, fissile materials, nuclear reactors and where special conditions apply.Roundslings conforming to BS EN 1492-4:2000+A1:2008 are suitable for use and storage in the following temperature ranges:a) polyester and polyamide: -40 C to 100 C,b) polypropylene: -40 C to 80 CBS EN 1492-4:2000+A1:2008 does not apply to the types of roundsling indicated below:a) roundslings designed for securing or lashing of cargoes to each other on pallets and platforms or in vehicles;b) slings of tubular webbing without filling.BS EN 1492-4:2000+A1:2008 deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the use of roundslings when carried out in accordance with the instructions and specifications given by the manufacturer or authorized representative.Cross References:EN 292-2:1991EN 292-2:1991/A1:1995EN 1050:1996prEN 1677-1:2000prEN 1677-2:2000prEN 1677-3:1998prEN 1677-4:1998prEN 1677-5:1998prEN 1677-6:1998EN 10002-2:1991EN 45012ISO/IEC Guide 62:1996EN ISO 9002:1994ISO 9002:1994ISO 1833ISO 2076ISO 12480-198/37/EC98/79/EC2006/42/ECIncorporates the following:AMD 16577 published 29 September 2006AMD 16577 is a Corrigendum. Amendment, June 2009. Amends and replaces BS EN 1492-2:2000