1.1 本规程规定了创建贴花（即粘土堆积）的程序，用于非平面软护甲测试项目后面，并将贴花粘贴到粘土块上。 注1: 本实践描述了单个贴花形状；其他形状可在其他标准中描述。 1.2 本规程旨在规定创建贴花的关键参数，以提高实验室之间测试设置的一致性。 注2: 在过去，非平面软装甲的测试要么是在测试项目后面用未指定的粘土堆积，要么是将测试项目平压在粘土块上。 1.3 本规程仅适用于为女性设计的非平面软体护甲。 1.4 本规程不适用于硬装甲测试项目。 1.5 本规程主要针对测试实验室，但可能适用于进行防弹衣抗弹道测试的防弹衣制造商、研究人员和最终用户。 1.6 在本惯例中，“其他标准和规范”和“除非另有规定”指需要使用本惯例的文件（例如，军事标准、采购规范）。购买者和其他用户负责“其他标准和规范”，并指定取代本规范的任何要求。 1.7 单位- 以国际单位制表示的数值应视为标准值。适当时，英寸- 出于信息目的，在括号中包含磅单位。 1.8 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.9 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 4.1 U、 美国国防部和美国司法部评估抗弹道躯干防弹衣性能的标准要求使用由Roma Plastilina 1号制成的背衬组件 ® . 必须以一致的方式在非平面软装甲测试项目后面创建贴花，以减少实验室内和实验室之间的可变性。 4.2 本规程适用于认证测试或研发测试。

1.1 This practice specifies a procedure for creating appliques (that is, build-up of clay) for use behind nonplanar, soft body armor test items and affixing the appliques to the clay block. Note 1: This practice describes a single applique shape; additional shapes may be described in other standards. 1.2 The purpose of this practice is to specify critical parameters for creating appliques in order to improve consistency of the test setup between laboratories. Note 2: In the past, testing of nonplanar soft armor has been done either with an unspecified buildup of clay behind the test item or with the test item pressed flat against the clay block. 1.3 This practice is applicable only to nonplanar soft body armor designed for females. 1.4 This practice is not applicable to hard armor test items. 1.5 This practice is primarily directed toward test laboratories but may be applicable to body armor manufacturers, researchers, and end users performing ballistic-resistance testing of body armor. 1.6 In this practice, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this practice. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this practice. 1.7 Units— The values stated in SI units are to be regarded as standard. Where appropriate, inch-pound units are included parenthetically for information purposes. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 U.S. Department of Defense and U.S. Department of Justice standards for assessing the performance of ballistic-resistant torso body armor require the use of backing assemblies made with Roma Plastilina No. 1 ® . The creation of appliques behind nonplanar soft armor test items must be done in a consistent manner to reduce variability within and between laboratories. 4.2 This practice is applicable for certification testing or for research and development testing.