ISO 262:2023-ISO通用公制螺纹-螺栓、螺钉、螺柱和螺母的选定尺寸-国家数字标准馆

现行 ISO 262:2023

到馆阅读

收藏跟踪

购买正版

ISO general purpose metric screw threads — Selected sizes for bolts, screws, studs and nuts ISO通用公制螺纹-螺栓、螺钉、螺柱和螺母的选定尺寸

发布日期： 2023-04-20

本文件规定了直径范围从1？毫米到100？mm的ISO通用公制螺纹（M），具有符合ISO 68-1的基本轮廓和设计轮廓。这些尺寸的直径和节距组合选自ISO 261。
本文件适用于公制商用紧固件螺纹。

This document specifies the selected sizes for bolts, screws, studs and nuts in the diameter range from 1？mm to 100？mm of ISO general purpose metric screw threads (M) having the basic and design profiles according to ISO 68-1. These sizes of diameter and pitch combinations are selected from ISO 261.
This document is applicable to the metric commercial fastener screw threads.

分类信息

发布单位或类别：国际组织-国际标准化组织

ICS分类： 21.040.10螺纹 - 公制螺纹

关联关系

研制信息

归口单位： ISO/TC 1

相似标准/计划/法规

ISO general purpose metric screw threads. Selected sizes for screws, bolts and nuts.
ISO通用公制螺纹螺钉、螺栓和螺母的选定尺寸

ISO general purpose metric screw threads - Selected sizes for screws, bolts and nuts (ISO 262:1998)
ISO通用公制螺纹螺钉、螺栓和螺母的选定尺寸（ISO 262-1998）

JIS B 0205-3-2001

ISO general purpose metric screw threads -- Part 3: Selected sizes for screws, bolts and nuts
ISO通用公制螺纹第3部分:螺钉、螺栓和螺母的选择尺寸

BS ISO 965-2-1998+A1-2021

ISO general purpose metric screw threads. Tolerances-Limits of sizes for general purpose external and internal screw threads. Medium quality
ISO通用公制螺纹公差

ISO general purpose metric screw threads. Tolerances. Limits of sizes for general purpose external and internal screw threads. Medium quality.
ISO通用公制螺纹公差通用外螺纹和内螺纹的尺寸限制中等质量

JIS B 0209-2-2001

ISO general purpose metric screw threads -- Tolerances -- Part 2: Limits of sizes for general purpose external and internal screw threads -- Medium quality
ISO通用公制螺纹公差第2部分:通用外螺纹和内螺纹尺寸限值中等质量

ISO general purpose metric screw threads - Tolerances - Part 2: Limits of sizes for general purpose external and internal screw threads - Medium quality (ISO 965-2:1998)
ISO通用公制螺纹-公差-第2部分:通用外螺纹和内螺纹的尺寸限制；中等质量（ISO 965-2-1998）

General purpose ISO metric screw threads - Nominal sizes for 1 mm to 68 mm diameter coarse pitch threads
ISO通用米制螺纹.第1部分:粗牙螺纹的标称尺寸；公称直径从1毫米到68毫米

BS ISO 965-5-1998+A1-2021

ISO general purpose metric screw threads. Tolerances-Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO通用公制螺纹公差

ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO通用公制螺纹——公差SPART 5:与热浸镀锌外螺纹配合的内螺纹尺寸限制镀锌前最大公差位置为h

JIS B 0209-5-2001

ISO general purpose metric screw threads -- Tolerances -- Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO通用米制螺纹公差第5部分:镀锌前最大公差位置为h的热浸镀锌外螺纹与内螺纹配合的尺寸限制

GOST ISO 965-5-2015

Основные нормы взаимозаменяемости. Резьбы метрические ИСО общего назначения. Допуски. Предельные размеры внутренних резьб, сопрягаемых с горячеоцинкованными наружными резьбами, соответствующими до нанесения покрытия полям допусков с основными отклонениями до h включительно
互换性的基本规范 ISO通用公制螺纹公差内螺纹尺寸的限制与热镀锌外螺纹配合镀锌前最大公差位置h

General purpose ISO metric screw threads - Nominal sizes for 3 mm fine pitch threads with diameters from 28 mm to 300 mm
ISO通用米制螺纹.第8部分:3mm细牙螺纹的标称尺寸；公称直径从28毫米到300毫米

General purpose ISO metric screw threads - Nominal sizes for 6 mm fine pitch threads with diameters from 70 mm to 500 mm
ISO通用米制螺纹.第10部分:6mm细牙螺纹的标称尺寸；标称直径从70毫米到500毫米

General purpose ISO metric screw threads - Nominal sizes for 2 mm fine pitch threads with diameters from 17 mm to 300 mm
ISO通用米制螺纹.第7部分:2mm细牙螺纹的标称尺寸；标称直径从17毫米到300毫米

General purpose ISO metric screw threads - Limits of size for 1 mm to 68 mm diameter coarse pitch threads with recommended tolerance classes
ISO通用米制螺纹.第9部分:4mm细牙螺纹的标称尺寸；标称直径从40毫米到300毫米

General purpose ISO metric screw threads - Nominal sizes for 1.5 mm fine pitch threads with diameters from 12 mm to 300 mm
ISO通用米制螺纹.第6部分:1.5mm细牙螺纹的标称尺寸；标称直径从12毫米到300毫米

General purpose ISO metric screw threads - Nominal sizes for 0.5 mm fine pitch threads with diameters from 3.5 mm to 90 mm
ISO通用米制螺纹.第3部分:0.5mm细牙螺纹的标称尺寸；标称直径从3.5毫米到90毫米

General purpose ISO metric screw threads - Nominal sizes for 0.75 mm fine pitch threads with diameters from 5 mm to 110 mm
ISO通用米制螺纹.第4部分:0.75mm细牙螺纹的标称尺寸；标称直径从5毫米到110毫米

ISO general purpose metric screw threads - Tolerances - Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing (ISO 965-5:1998)
ISO通用米制螺纹公差第5部分:镀锌前最大公差位置为h的热浸镀锌外螺纹与内螺纹配合的尺寸限制

《国家标准化发展纲要》提出建设国家数字标准馆，推动标准化工作向数字化、网络化、智能化转型。中国标准化研究院正在全力推进国家数字标准馆建设，力争在2026年底建成“一个中心”和“一个平台”，即全球领先的标准数据资源中心，涵盖标准全生命周期的数字化、网络化、智能化研究与服务平台。

专题数据库

标准管理系统

大数据分析系统

标准智能研制系统