BS EN 3021:2017规定了石墨和无卤钼的鉴定和试验要求 二硫化物干膜润滑剂。相关润滑剂的微动、腐蚀、磨损和摩擦性能的测试要求和测试如下: 不属于本标准的一部分。参考规范性引用文件中的相关标准。本标准中规定的所有测试必须经过润滑剂制造商的认证。为了获得具有规定厚度和最佳附着力的均匀涂层，喷涂 建议与热固化结合使用。交叉引用:EN ISO 1519（ISO 1519:2011）ASEN ISO 9227:2012ISO 2811-1:2011 Ed 2ISO 3270:1984（R08）EN ISO 2409（ISO 2409:2013）ASEN ISO 2811-4（ISO 2811-4:2011）ASEN ISO 1513（ISO 1513:2010）ASEN ISO 2808（ISO 2808:2007）ASISO 2812-1:2007 Ed 2（R10）EN ISO 2811- 1（ISO 2811-1:2011）ASISO 8504-2:2000ISO 4628-2:2003 Ed 2ISO 4618:2014 Ed 2EN 3027EN 3026EN 3847EN 3030ISO 11075:2007 Ed 2EN ISO 9117-6（ISO 9117-6:2012）ASISO 1519:2011 Ed 3EN ISO 6270-1（ISO 6270-1:1998 AS）ISO 2811-3:2011 Ed 2ISO 2811-2:2011 Ed 2ISO 1523:2002 Ed 3EN 10204:2004EN ISO 1523（ISO 1523:2002 AS）EN ISO 4628-2（ISO 4628-2:2016）ASISO 1514:2011808080ISO 2808:2007 Ed 4（R10）EN 2491:2011ISO 9117-1:2009 Ed 1ISO 6270-1:1998（R08）EN ISO 2811-2（ISO 2811-2:2011）ASEN ISO 8504-2（ISO 8504-2:2000 AS）ISO 11078:2007 Ed 2ISO 9227:2012 ED3ISO 2812-2:2007 Ed 2（R10）ISO 2431:2011EN 3840:2007ISO 3675:1998ISO 2409:2013 ED4EN ISO 1524（ISO 1524:2013）ASEN ISO 2812-2（ISO 2812-2:2007）ASEN ISO 2818-20119117-6:2012 ED1EN ISO 2431（ISO 2431: 2011）ASEN ISO 9117-1（ISO 9117-1:2009）ASISO 3675:1998（F）EN ISO 2812-1（ISO 2812-1:2007）ASISO 1524:2013 ED4EN 2497:1989购买本文件时可获得的所有现行修订均包含在购买本文件中。

BS EN 3021:2017 specifies the qualification and test requirements for graphite and halogen free molybdenum disulphide dry film lubricant.Test requirements and testing of fretting, corrosion, wear and friction properties of relevant lubricants are not part of this standard. Refer to relevant standards in normative references.All testing defined in this standard has to be certified by the manufacturer of the lubricant.In order to achieve uniform coatings with defined thickness and best adhesion properties, spray application in combination with heat curing is recommended.Cross References:EN ISO 1519 (ISO 1519:2011) ASEN ISO 9227:2012ISO 2811-1:2011 Ed 2ISO 3270:1984 (R08)EN ISO 2409 (ISO 2409:2013) ASEN ISO 2811-4 (ISO 2811-4:2011) ASEN ISO 1513 (ISO 1513:2010) ASEN ISO 2808 (ISO 2808:2007) ASISO 2812-1:2007 Ed 2 (R10)EN ISO 2811-1 (ISO 2811-1:2011) ASISO 8504-2:2000ISO 4628-2:2003 Ed 2ISO 4618:2014 ED2EN 3027EN 3026EN 3847EN 3030ISO 11075:2007 Ed 2EN ISO 9117-6 (ISO 9117-6:2012) ASISO 1519:2011 Ed 3EN ISO 6270-1 (ISO 6270-1:1998 AS)ISO 2811-3:2011 Ed 2ISO 2811-2:2011 Ed 2ISO 1523:2002 Ed 3EN 10204:2004EN ISO 1523 (ISO 1523:2002 AS)EN ISO 4628-2 (ISO 4628-2:2016) ASISO 1513:2010 Ed 4ISO 2811-4:2011 Ed 2EN 4160:2011ISO 8080ISO 2808:2007 Ed 4 (R10)EN 2491:2011ISO 9117-1:2009 Ed 1ISO 6270-1:1998 (R08)EN ISO 2811-2 (ISO 2811-2:2011) ASEN ISO 8504-2 (ISO 8504-2:2000 AS)ISO 11078:2007 Ed 2ISO 9227:2012 ED3ISO 2812-2:2007 Ed 2 (R10)ISO 2431:2011EN 3840:2007ISO 3675:1998ISO 2409:2013 ED4EN ISO 1524 (ISO 1524:2013) ASEN ISO 2812-2 (ISO 2812-2:2007) ASEN ISO 4618 (ISO 4618:2014) ASEN ISO 2811-3 (ISO 2811-3:2011) ASISO 9117-6:2012 ED1EN ISO 2431 (ISO 2431:2011) ASEN ISO 9117-1 (ISO 9117-1:2009) ASISO 3675:1998 (F)EN ISO 2812-1 (ISO 2812-1:2007) ASISO 1524:2013 ED4EN 2497:1989All current amendments available at time of purchase are included with the purchase of this document.