1.1 本规范涵盖了在机构和家庭环境中使用的机织和针织厨房毛巾、洗碗布、防撞毛巾、哈克毛巾、面巾、手巾、浴巾和浴巾产品中重要的特定性能特征的评估。 1.2 本规范可通过买方和供应商之间的相互协议用于建立采购规范要求。 1.3 这些要求适用于与织物方向相关的那些属性的长度和宽度方向。 1.4 本规范不适用于涂层和层压产品、非织造产品或用于服装的毛圈织物。 1.5 本标准并不旨在解决与其使用相关的所有安全性问题（如果有）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践并确定法规限制的适用性。1.6 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ======意义和用途====== 5.1 经买方和供应商双方同意，用于该最终用途的机织或针织产品应满足 表1 毛圈产品的本规范 表2 适用于非毛圈产品。 5.2 人们认识到，出于时尚或美学的目的，由这些织物制成的制品的最终消费者可能会发现不符合以下所有要求的可接受产品: 表1 或 表2 因此， 表1 或 表2 可由买卖双方协商修改。 5.2.1 在这种情况下，对本规范的任何引用应说明:本产品符合ASTM规范63-707，但以下特性除外。 5.3 如果买方和供应商之间没有达成预购协议，并且在发生争议时， 表1 或 表2 仅用作指南。如 5.2 最终消费者需求决定了任何特定样式的不同性能参数。 5.4 特定性质和测试方法的重要性和用途在指定测试方法的适当章节中讨论。

1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knitted kitchen towel, dishcloth, crash towel, huck towel, washcloth, hand towel, bath towel, and bath sheet products for use in institutional and household environments. 1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements. 1.3 The requirements apply to the length and width directions for those properties where fabric direction is pertinent. 1.4 This specification is not applicable for coated and laminated products, nonwoven products, or terry fabrics used for apparel. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 Upon mutual agreement between the purchaser and the supplier, woven or knitted products intended for this end use should meet all of the requirements listed in Table 1 of this specification for terry products and Table 2 for non terry products. 5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1 or Table 2 . Therefore, one or more of the requirements listed in Table 1 or Table 2 may be modified by mutual agreement between the purchaser and the seller. 5.2.1 In such cases, any references to the specification shall specify that: This product meets ASTM Specification 63-707 except for the following characteristic(s). 5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 or Table 2 are intended to be used as a guide only. As noted in 5.2 , ultimate consumer demands dictate varying performance parameters for any particular style. 5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.